The current waveforms of a capacitor are shown in Figure below. Determine the average, root mean square (rms), and peak current ratings of the capacitor. Assume Ipeak = 400 A of a half sine- wave. fiA p ^ ( 0 t 11 13 T, = -1/, fs -200 100 μs fs 250 Hz = = 1₁ 1₂ = 300 μs 500 pus 13 12

The current waveforms of a capacitor are shown in Figure below. Determine the average, root mean square (rms), and peak current ratings of the capacitor. Assume Ipeak = 400 A of a half sine- wave. fiA p ^ ( 0 t 11 13 T, = -1/, fs -200 100 μs fs 250 Hz = = 1₁ 1₂ = 300 μs 500 pus 13 12

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Related questions

Q: 3.6 In a boron-doped silicon layer with impurity concentration of 1017/cm³, find the hole and…

A: Given that, Boron concentration (Acceptor Concentration) Na = 1017/cm3…

Q: Find the SAE's for the assigned loop currents. Solve for loop current 22 (in amps)_

A: For the given circuit the value of the unknown loop 2 current needs to be calculated by deriving…

Q: Write the node equation for V3. www R₁ R4 Vs 1₁ R5 R3 W 1₂ T R₂ R6 V3 R7 Ro R8 M V4

A: The given circuit isWe need to write the node equation for V3.

Q: R₁ ww K₁ = K₂= K3 = 40 mH io av t = 0 WW ww + 140 V R₂ 10 A The switch has been open for a long time…

Q: 2. a) A conductor with cross-sectional area of 10 cm² carries a conduction current 0.2 sin10ºt mA.…

A: Given data:for (a):for (b) asked to explain the reasons for using AC instead of DC voltage,

Q: P2 Find V. in the circuit using nodal analysis. 6/0° V www 1Ω Page 3 of 8 2/0° A -jin 2V, 192 V₂

A: The given circuit isWe need to determine the voltage, Vo using nodal analysis.

Q: 2. Determine i(t) in the circuit below for t≥0. 0.2 V 0.122 w 0.2 H İL mom 1=0/ 0.1 V 0.3 2 www 0.2…

A: The given circuit isWe need to determine the current iL(t) for t≥0.

Q: Q#3: A single-phase transformer has the following specifications Apparent Power (S) = 10 kVA Primary…

A: The apparent power, Primary voltage, Secondary voltage, The frequency,

Q: Upload your work to the submission box below. Find the Thevenin equivalent resistance (in Ohm up to…

A: Thevnin's theorem is used to simplify complex electrical circuits into simpler equivalent circuits,…

Q: The circuit shown below has an LED with forward bias of 1.2 V, and the BJT has the following values…

A: Given:a circuit, with, we need to find:Total current through the LED.

Q: Apply the loop rule and junction rule with sign convention from lecture find /₁, 12, and 13.

A: For the given circuit the value of the current I1, I2 and I3 needs to be calculated by using the…

Q: • There are two uniform line charges of density p₁= +4nC/m at y=4, z=5, the second line charge p₁ =…

A: The uniform line charge densities are given by⇒ρl1=+4nC/m located at y = 4, z = 5.⇒ρl2=−4nC/m…

Q: Find the transfer function using both Block Diagram Reduction and Signal Flow Graph H3(s) R(s) H₁(s)…

A: Given:Block diagram of a control system, To find:Transfer function using block diagram reduction and…

Q: 1 4 2 13 3 -VXY Is 4 Y X

A: the current and voltage difference phase angle is goes as followsFor pure capacitor current leads…

Q: Determine V_o using Thevenin's theorem 1kΩ ww 12 V www 6V 1kΩ ww 1kΩ 4 mA Vo

A: The given circuit isWe need to find the voltage, V0 using the Thevenin's theorem.

Q: 3. Find vo(t) for t> 0 in the network shown and plot the response, including the time interval just…

A: The given circuit isWe need to find and plot v0(t) for t > 0.

Q: Problem 4: Find the Norton equivalent with respect to the terminals ab for the circuit shown below.…

A: Given circuit:Asked to find the Norton equivalent circuit across the terminals a and b

Q: 4) Find the steady-state response i。(t) for the network below (use Laplace transforms). i₁(t) 4 cos…

A: The given circuit is We need to find the steady state response io(t) using Laplace transform.

Q: 2. The three loads in Figure 2 are connected in parallel and the voltage across them is Vo 10020 V…

A: The three loads are connected in parallel as shown below,Here,the voltage,Vo = . The loads can be…

Q: A dc source is connected to a series RLC circuit by a switch that closes at t = 0, as shown in…

A: Given:a series RLC circuit with dc source, the switch is closed at t=0. we need to find:a) the…

Q: Find vo. I 2.4 Α Μ τη 24 Ω (1.2A, 12 Μ 18 Ω 16 Ω 12 Ω ig 15 V

A: given a circuit and asked to find the voltage V0.

Q: A single-phase 100 kVA, 2400/240 V, 60 Hz step-down transformer is connected to a load on the…

A: Given circuit:Asked to find the voltage V1 primary side?

Q: In the below circuit, the transistor has ß = 40. a) Find the values of VB, VC, and VE. b) If RB is…

A: GivenA BJT circuit is given as,The current gain is .To findThe values of , and .The values of ,…

Q: There is no energy stored in the circuit in Fig. P 2 when the switch is closed at t = 0. Find vo(t)…

A: In the given questions we need to calculate the output voltage.

Q: P4.30. For the circuit shown in Figure P4.30, the switch is closed for a long time prior to t = 0.…

A: The circuit diagram,

Q: Problem 7. For the given circuit, find i(t) for t > 0. is(t) = 4 A, t 0 11 Is(t) 4 i(t) R3 30Ω R4…

A: The inductor is pasdive components in circuit. In magnetic field it store energy. The resistor is…

Q: For the circuit shown in the given figure, assume vst=-2 V. VS2=2sin (2mx2000) V. R₁ = 100 kohm,…

A: We need to find out the output voltage for the inverting summing amplifier.

Q: Use a Karnaugh map to simplify the function: Z = f(A, B, C, D) = Σ(2, 3, 4, 5, 10, 11, 15) with…

A: Given minterms

Q: A diode taken from the following circuit was previously tested by applying 0.75V from anode to…

A: The given circuit diagram is shown below,

Q: V(t) = 5 los (wt + 75°) - 3 los (wt-75) +4 Find Vm and O 1. Find Vm (Volt)? 2. Find 8 (°)? a = Vm…

A: To find the maximum amplitude Vm and the phase angle, we will first simplify the given expression.…

Q: Using the Laplace transform, find the current i(t) in the circuit below, assuming zero initial…

A: The given circuit isThe initial conditions are zero.i.e the zero initial current and zero charge.i.e…

Q: QUESTION S In a 50-ohm system, what is the normalized admittance, yin, associated with a voltage…

A: Question (5).50-ohm systemvoltage coefficient magnitude of 0.6Angle of .We need to find normalized…

Q: 4.27 In the circuit shown in Fig. P4.27, D, has 10 times the junction area of D₂. What value of…

A: The circuit diagram,The junction area of diode D1 is 10 times the junction area of diode D2,The…

Q: 1. For the given circuit below, find the current in the circuit assuming a silicon diode and forward…

A: Given a circuit with 4 diodes and 2 voltage sourcesNeed to find the current flowing through the…

Q: Find the value of i(t) at t = 0, t = 1s, and t = 3s. 2u(t-2) V(+ Answer: i(t = 0) = 0 Answer: i(t =…

A: Given:a circuit,To find:the value of current i(t) at t=0, 1, 3 sec.

Q: 3 For the system define by the pole zero plot be low. X -2 -1 2 s-plane x Find the system out put…

A: Given plot isAsked to find the output of the system

Q: Required information The half-wave rectifier in the figure given below is operating at a frequency…

Q: There is no energy stored in the circuit in (Figure 1) at t = 0. Figure lig 200 Ω 250 nF Vo 3.75 x…

A: Given Data:An RLC circuit with,The independent current source The passive elements The dependent…

Q: Problem-6: Is the signal x(n)-7 cos(xn/2) a power signal or energy signal? Find its value (either…

A: Given that signal x(n) is x(n)= 7 cos() is x(n) is power signal or…

Q: Use linearity and the assumption that V = 1V to find the actual value of V. 2 ΚΩ Μ 2 ΚΩ www Μ 2 ΚΩ…

A: In this question, we need to determine the actual value of voltage Vo . We solve this problem by…

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

Please answer in typing format solution please yy

Please answer in typing format

Please answer in typing format i will be like it

The current waveforms of a capacitor are shown in Figure below. Determine the average, root
mean square (rms), and peak current ratings of the capacitor. Assume Ipeak = 400 A of a half sine-
wave.
0
-200
i₁A
1₁
t₁ = 100 μµs f = 250 Hz
11
t₂ = 300 µs
13 = 500 µs
12
13
T₁ = 1/1/12
S
fs

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: what is given and what to do:

VIEW

Step 2: part a - Finding average value:

VIEW

Step 3: part b)- finding rms value:

VIEW

Step 4: part c) - finding peak current rating:

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A square waveform with following specifications. Peak to Peak current 10A Time for ten cycles 0.04s i. Sketch the waveform. i. Determine the Form factor and peak factor for the above sketched waveform
In an experiment, the function generator is adjusted to generate a square voltage at a certain frequency. This voltage is displayed on an oscilloscope and the reading is 10 V peak-to-peak. The rms value of this voltage is .What will be the rms value of this voltage if the frequency is reduced to the half value? 3.536 Vrms . 3.536 Vrms O 5 Vrms . 1.7677 Vrms O 3.536 Vrms. 1.7677 Vrms O 5 Vrms . 5 Vrms ...... O 10 Vrms . 10 Vrms ......
In an experiment, the function generator is adjusted to generate a square voltage at a certain frequency. This voltage is displayed on an oscilloscope and the reading is 16 V peak-to-peak. The rms value of this voltage is .What will be the rms value of this voltage if the frequency is doubled? Select one: O 16 Vrms 32 Vrms O 8 Vrms . 8 Vrms ..... O 5.657 Vrms 5.657 Vrms ....... O 8 Vrms . 16 Vrms O 16 Vrms 8 Vrms ......
Help
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]
The sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 50 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3.6 cm and the peak to peak height is 5.8 cm. Determine the following: The frequency is = The peak to peak voltage is = The amplitude is = The R.M.S voltage is =
AC 15. What would the equivalent resistance be of a 159 uF capacitor? 16. What is the RMS voltage of a circuit if the peak voltage is 170 volts? 17. If the RMS voltage is 240 volts AC, what is the peak voltage? 18. What is the formula for finding an inductors equivalent resistance? 19. What is the equivalent resistance of an inductor with 0.17 henrys? 20. What is the symbol of an AC power source? 21. What is the equivalent inductance of a parallel circuit with a 0.01L, 0.02L, and 1.7L inductor? 22. What is the equivalent inductance of a series circuit with a 0.03L, 0.04L, and 1.6L inductor? 23. A transformer with a primary voltage of 480 volts and a turns ratio of 2:1 will have what secondary voltage? 24. A Power Network is comprised of what three components? 25. What is the main difference between a fuse and a circuit breaker?
Find the RMS value..
A 10.0-μF capacitor and a 2.00-H inductor are connected in series with a 60.0-Hz source whose rms output is 100 V. Finda. the rms current in the circuit.b. the voltage drop across the inductor. c. the voltage drop across the capacitor.
A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
q11
The rms value of the resultant current in a wire carries a dc current of 10 A and a sinusoidal alternating current of peak of value 20 A is-