The current through the 4702 resistor in the circuit in Figure 1 is

Q: A certain voltage is +11.1 V for 21.8 ms and -11.1V for the succeeding 21.8 ms and continues…

A: For the first time at , .For the succeeding , .The resistance value is .

Q: Problems 5-7 Simplify the block diagrams using “rules” of simplification.

A:

Q: What should the resistors R1, R2, R3 and R4 be so that the gain of the circuit is 2.2

A:

Q: The total turn ON time of SCR is 40 µs. If the sum of delay and spread time is 8 us, the rise time…

A: for a scr , ton=tdelay+trise+tspread given tdelay + tspread = 8 μs and ton = 40 μs

Q: (b) For the given circuit please answer the following questions (i) Name the whole circuit. (ii)…

A: For the given circuit, (i) The given circuit is a 4-bit asynchronous down counter.   (ii) The…

Q: P7. Find out the thermal noise if the room temperature is 300 K and the noise bandeidth is 3.5 kHz.

A: Given: Room temperature,T0=300 K Noise bandwidth, Bn=3.5 kHz

Q: A) Determine the current through the R9 resistor and the voltage across the R7 resistor. B) Measure…

A:

Q: Explain the relationship between M18 and M19?

A:

Q: State which elements do and do not consume in an RLC circuit

A: Given : In the question they want to know for which range of frequency which element will consume…

Q: For the following circuit, Vsrc=1.5 V and Rload3D225 Q. What is VR? Is + Vsrc VR Rload 6.7 mV 1.5 V…

A:

Q: What is the dc output voltage and ripple in given example? Sketch the output waveform.

A: Given Transformer ratio as 7:1  Vp = 120 V C1 = 68 if, RL = 2.2 kohm

Q: Voltage division rule is used for both series and parallel circuit for the measurement of voltage…

A: According to the given question, it is required to determine whether the below given statement is…

Q: The number of Hamilton Circuits in K20 is

A: Hamilton Circuits:A Hamilton circuit is one that passes through each point exactly once cover all…

Q: Q7. In Figure X shown below: a. Identify the biasing configuration b. Draw the equilvalent circult…

A: Given circuit is belongs to mosfet circui

Q: 4. Calculate the Elmore time constant from node A to node B of the following RC network. R₁ = R₂ =…

A:

Q: 7 With a counter 10 lights will be controlled. At the first clock pulse all lights will be ON (1).…

A: Number of the counter lights to be controlled is 10. The objectives of the counter for the given…

Q: The frequency is relating to time period--

A: In this question we need to answer how frequency is relating to time period.

Q: Safety Precautions in the Electrical Engineering Laboratory

A: It’s vitally important to take safety precautions when working with electricity. This precaution…

Q: In measuring settling time from step response with five percentage tolerance, the tolerance band…

A: Answer: b. 0.95 and 1.05   Explanation:   a. It is not a valid option. the values 0.94 and 1.06, it…

Q: Q7/B: Define the sag and list the factors affecting it.

A: Based on the power system

Q: Find Norton equivalent circuit for the following circuit with respect to terminals A - B " Norton's…

A:

Q: The Star Connection Recap

A: Star connection: In the Star Connection, the similar ends of the three windings are connected to a…

Q: In the network given in the figure, create protection with overcurrent time relays with a minimum…

A:

Q: error ratio usng block reduction

A:

Q: Q2Detemine the current Ipr, Ipz and Igt for the circuit show below to R Si 5.3/2 E 20 D.Y Si

A: Given circuit, Let's assume resistor R2=5 kΩ to complete the circuit.

Q: Q4) Derived and Determine Zin, Zo, AV and AI. 8v

A:

Q: f(t)

A:

Q: The proper shaping of the load curve or load characteristics cannot be done by relieving the…

A: Load curve is the graphical representation of load in proper time sequence and the time in hours. It…

Q: In sequential circuit, write the state table of the following sequence: 00, 01, 10, 11, 10 and…

A:

Q: A R7 2kQ +|1| C V3 15 V R11 3kQ R9 ww 1kQ R8 ww 3kQ D R12 3kQ R10 ww 1kQ **

A:

Q: Electric ovens are mostly (a) resistive (b) capacitive (c) inductive (d) both a and c

A:

Q: compare the charasteristics of series with those of parallel circuit s,what are their differences ?…

A: In this question we need to compare the charasteristics of series with those of parallel circuit

Q: Two carpenters are hammering at the same time, each at a different hammering frequency. The…

A: The absolute disparities between the two frequencies add up to the beat frequency. A beat is…

Q: An L-R series circuit consists of an inductor with inductance, L, connected in series with a…

A: KVL equation in the loop will beE=LdIdt+RIdIdt+RLI=1LE-----1Generalized 1st order differential…

Q: B B C C Lo D D

A: 1) Given

Q: 3. The current that should pass through the RTD is: Оа. 5.7 mA O b. 10 mA Ос. 5 mA d. 11.5 mA

A: RTD , An RTD is a passive device The current that should pass through the RTD is

Q: The most commonly used demodulation technique for FSK uses circuit.

A: According to the question we have to discuss about the most commonly used demodulation technique for…

Q: In sequential circuit, write the state table of the following sequence: 00, 01, 10, 11, 10 and…

A: Given: The sequence of a sequential circuit, 00, 01, 10, 11, 10 and repeats. To find: we have to…

Q: control and trasbfer functoon

A: Given:

Q: How do I create a circuit that does the following. The output voltage Vout is at OV originally. If…

A: According to the question, we need to design a regulator circuit that provides the maximum output…

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.