The cross-section of a pretensioned prestressed concrete beam is shown in figure. The reinforcement is place concentrically. If the stress in steel at transfer is 1000 MPa, compute the stress in steel immediately after

The cross-section of a pretensioned prestressed concrete beam is shown in figure. The reinforcement is place concentrically. If the stress in steel at transfer is 1000 MPa, compute the stress in steel immediately after

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 480 µɛ is measured from a strain gage located at c = 5 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P 3P |1 Strain gage- d D E 2 H b Answer: P= i N
Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Bronze A (in.²) Steel 2 ft E (psi) Ow (psi) Aluminum 4 ft 3 ft 2P Steel 0.75 30 × 106 20 000 Bronze 1.00 12 x 106 18 000 ЗР 4P Aluminum 0.50 10 × 106 12 000 Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.
1. Find the properties of equal-leg angle bar 150 x 50 x 6.0 in metric. 2. Find the full section properties of LC shapes steel bar 100 x 50 x 15 x 3.0 in metric. 3. A stress that lies between the proportional limit and the upper yield point of a steel. What is 5 and 5 Show the relationship uring a graph of mild structural stool
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa], located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. K4N/M 2m B 10kN/mm 4m 2m D Steel Aluminum 42mm 20 mm 13 mm
A composite beam is made of two brass [E = 97 GPa] plates bonded to an aluminum [E = 72 GPa] bar, as shown. The beam is subjected to a bending moment of 2420 N-m acting about the z axis. Assume b=64 mm, d1=36 mm, d2=13 mm. Determine: (a) the maximum bending stresses opy,Gal in the brass plates and the aluminum bar. (b) the stress in the brass obrj at the joints where the two materials are bonded together. Brass (2) d2 Aluminum (1) Brass (2) dz b Answers: (a) obr = i MPa, oal = i MPа. (b) Obrj MPa.
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 270 mm, a wall thickness of 15 mm, and a length of 5.5 m. The pipe supports a compressive load of 635 kN. After the temperature of the pipe drops 45°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
Sketch the stress-strain curve and explain it in relation to the tensile test for steel bars.
The composite bar is firmly attached to unyielding supports. The bar is stress-free at 50°F. Compute the stress in each material after the 80-kip force is applied and the temperature is increased to 100°F. Use a = 6.5 x106/°F for steel and a = 12.8 x106/°F for aluminum. Aluminum A = 2 in.² E = 10 x 106 psi 15 in. Steel A = 3 in.2 E = 29 × 106 psi 80 kips 10 in.
The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown. It is subjected to a moment of M = 6.3 kN?m .Ebr = 100 GPa, Est = 200 GPa A: Determine the maximum bending stress in the brass. B:Determine the maximum bending stress in the steel. C: Determine the stress in the brass at the seam where the brass and steel are bonded together. D:Determine the stress in the steel at the seam where the brass and steel are bonded together. B M 175 mm 150 mm 200 mm