The Crosby gage tester shown in Figure 4 is used to calibrate or to test pressure gages. When the weights and the piston together weigh 140 N, the gage being tested indicates 200 kPa. If the piston diameter is 30 mm, what percentage of error exists in the gage? Weights- L Piston Figure 4 Air Oll

Q: If the gage reading at (A) is (pA=1OkPa), find the gage reading at (B) in (Pa) and in (mm Hg)?…

A: Write the given values with suitable variables. PA=10 kPa Consider, a reference line of the…

Q: 1. What are the base units of the SI and U.S. Customary systems? 2. What is the definition of an…

A:

Q: Suppose that you have a dead weight tester with a maximum reading of 50 bar. If the diameter of the…

A: The total mass of the weight, pan and piston would you need in units of: a. lbm : 320.3 lbm b. kg :…

Q: →→Moving to another question will save this response. Question 5 For the extension of the cylinder…

A: Given: For the extension of the cylinder shown below, a force of F = 450N is needed. If the…

Q: As a part of your job, your role is to investigate the behavior of a hydraulic system that is…

A: Consider the diagram shown below for the given system. According to the Pascal's law, the pressure…

Q: Explain, with the aid of diagrams, the operation of two different pressure transducers, one which…

A: A transducer is a device that is used for converting one form of energy into electrical signals.…

Q: 2.11.11 Replace 1-ft with 0.3 m, 2-ft with 0.6 m, 0.1 psi with 700 Pa, 0.5 ft with 0.15 m. 2.11.11…

A:

Q: Pascal = (0.01 bar, 0.001 bar,0.0001 bar, 1O 100.000 bar)and T= 500 rankine what is the value in…

A:

Q: In the figure shown, determine the reading of the gauge A. Solution oil (s.g30.8) 2.4m 2.7m water…

A: It is required to determine pressure at A

Q: Gauge A reads P= 701725 Pa gauge. What is the height h of the water in m, the air pressure is 180…

A: Absolute pressure = 180KPa  change into gauge pressure Pgauge=Pabs-Patm=180-101.3=78.7KPa=78700Pa

Q: Define Some basic pressure gages.

A: The pressure gauges are broadly classified into three types: Hydrostatic Gauges Aneroid Gauges…

Q: reading shown? For the 6 psi. The fluid in both pines A and B is water

A: we will use the equation of inclined tube manometer PA+γ1h1γ2I2 sinθ-γ3h3 =PB

Q: What is the magnitude of the force on an inclined gate shown? The tank contains water and is…

A:

Q: Solve with the correct units 6. A square block weighing 1.1 kN and 250 mm on an edge slides down in…

A: GivenW=1.1kNa=250mm=0.250mθ=20ot=6μm=6×10-6mν=7mPa.s =7×10-3 Pa. s

Q: Fluid Mechanic : The cylinder shown is the diagram is made from uniform material. What is its…

A: Given:-          Weight of the cylinder = ρvg= ρg×π4d2×750           water buoyancy = ρwvsg =…

Q: The system shown in the figure is used to accurately measure the pressure changes when the pressure…

A:

Q: gauges G, and G, install r and Pe = 1.00 bar. Th ATMOSPHERIC PRESS %3D G2

A:

Q: Vertically 300lb/pulg2 and horizontally 150 lb/pulg2 I have only this data please answer.

A: Giver:- My=300 lb/pulg2 Mx=150 lb/pulg2   To find:- Resultant

Q: A compressed gas cylinder in air at normal conditions has a gauge pressure of 3.0 atm. What pressure…

A:

Q: of pressure include?

A: Given :- Standard of pressure .

Q: The given figure is a representation of a piston inside a cylinder. What do you call parts A, B, C,…

A: given figure is a representation of a piston inside a cylinder. To name the parts A, B, C, D, &…

Q: A water column in a glass tube is used to measure the pres sure in a pipe. The tube is 1/2 in. in…

A: Given:Diameter of the tube, d1=12in  ; d2=18in  ; d3=16inFind: Water column due to surface tension…

Q: Using only Table A (Conversion of Units), calculate the values asked.  All answers must be given…

A:

Q: What is the pressure outside of a tire if the gauge pressure reads 32 psi and the interior of the…

A: Given data,  Gauge pressure of tire is Pg=32 psi  Interior of tire pressure is Pabs=47 psi

Q: A vacuum gauge connected to a steam condenser shows that the pressure inside the condenser is 0.783…

A:

Q: The area information is given as following. A,=338.6mm A=338.6mm A=233.5mm A-170.2mm A-255.2mm…

A: The area information is given as following. A,=338.6mm² A₂=233.5mm² 211 A,=84,6mm² A, 170.2mm²…

Q: For each of the following statements, answer TRUE or FALSE and explain your answer briefly.   In…

A:

Q: A pneumatic system is producing 120lb/in^2 of gauge pressure. It has been determined that 7 lb of…

A:

Q: If the vernier gauge reading for a specimen is 21.22 mm and the average DTI observation is 3…

A: Vernier gauge reading = 21.22 mm DTI observation = 3 divisions    Find out: The actual size of the…

Q: Convert the reading of pressure to kpa. Assuming that borometer reads 760 mm of Hg. (a). 1.35 m H₂o…

A: To find:  The pressure in kPa. Given : The barometer reading Patm=760 mm of Hg. The density of water…

Q: Please correctly answer all parts of the question. Thank you will upvote if correct!

A: (2) The Pirani gauge is a robust thermal conductivity gauge used for the measurement of pressures in…

Q: In Bourdon Gauge experiment, if the mass of the piston is 340 gr and mass of the platform is 173 gr,…

A: Mass of piston = 340 gr Platform mass = 173 gr Absolute pressure error = 218.9 Pa

Q: * When a mass of 1.2 kg is Applied on Piston area of 324 mm2. That means the pressure value equal to…

A: Given: m=1.2 kgA=324 mm2

Q: What is the specific? weight of nitrogen in units of new temper cubeter. at the temperature of minus…

A:

Q: For the hydrometer designed in Problem 13, what will be the specific gravity of the fluid in which…

A:

Q: Most pressure gages only have one unit representation, either in SI or English units a. True b.…

A: False

Q: Dissection : 1- Discuss the types of pressure devices and what are the uses of each type. 2- What is…

A: Physical devices that are used to find the pressure exerted by the the fluid are the Bourdon gauge…

Q: VII . Observation| Mass of piston, m=0.5Kg Area of piston, A = 254.46 x 10 m2 Actual Pressure =…

A: The pressure in the cylinder is given by the formula- Pact=mgA where m is the mass of the piston…

Q: In calibration of instrument the 0.055 percent of the calibration span what does it mean. If let say…

A: The calibration span is the total range of the instrument's observing range, which means the…

Q: A thermometer reading 10°C is brought into a room with a constant temperature of 33°C. If the…

A: Given data as per the question Room temperature =330 c Reading of thermometer after 3 minutes =150 c

Q: The surface tension of a fluid is a measure of its resistance to deformation. Select one: True False

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.