The critical angle of a medium for a specific wavelength, if the medium has relative permittivity 3 and relative permeability 4/3 for this wavelength, will be
Q: If the gain of the effective medium in a laser is (1.05) and the reflectivity coefficient of its…
A: Consider the given data as below. The effective medium in laser, G=1.05 The reflectivity coefficient…
Q: A metallic bar of cross-section Ao = 103 mm² and length Lo = 0.1 mm, is subjected to = 1600 N, the…
A: Given: The cross section area of the metallic bar is 103 mm2. The original length of the…
Q: A body of mass 500 kg is suspended on the free end of an iron wire of length 3 m and cross-sectional…
A:
Q: A substrate of intrinsic silicon, if the mobilities are given as followings: Hn = 1350 (T/300)-3/2…
A: Given the mobilities of the electron and holes. And the value of the intrinsic carrier concentration…
Q: In part (b), do I need to take over the relative permittivity of AIR, that mean C new =…
A:
Q: Compute the pressure in Nm2 required to compress a given volume of water V, to 99 percent of its…
A:
Q: 1) Determine the largest weight W that can be supported by two wires shown in Fig. below. The stress…
A: Draw the free body and force diagram as below. As given, The stress on both wires,…
Q: A batch of casted mild steel has a modulus of elasticity of 200 GPa and a yield strength of 250MPa.…
A: Given: The modulus of elasticity is 200 GPa. The yield strength is 250 MPa. Introduction: The…
Q: "Using a 1-kg load at a specified joint, your experiment displayed that the bottom chord experienced…
A: Given, Experimental value of FBC = 2.1 N (tensile) Theoretical value of FBC = 2.2 N (tensile)…
Q: 2.31. The three principal stresses at a given point are o=60 MPa, o2=-100 MPa, 03 =-10 MPa. If the…
A: Given: The principal stresses at a given point are 60 MPa, -100 MPa and -10 MPa. Introduction: The…
Q: At what dislance is the KE. Of paulticle . af performing SHM. 'amplilāde locm, three Times is…
A: Have a look
Q: IF NUMBER OF Si 15 4 997 x 10 THE ATOMS LATTICE CONSTANT OF SILICON IS S.4A; AND THE ATOMS IN CUBIC…
A:
Q: 4. (a) Calculate the Debye frequency op for a monoatomic sc (simple-cubic) material with the lattice…
A: Given, Lattice spacing, a=0.3×10-9m Speed of sound, c=3000m/s According to Debye's model,…
Q: "Using a 1-kg load at a specified joint, your experiment displayed that the bottom chord experienced…
A: Given in question: Actual force(F) = 2.75 N Measured force(F') =…
Q: Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure…
A: Given, P = 100 atmosphere = 100 x 1.013 x 105 Pa Final volume, V2 = 100.5 l = 100.5 ×10 –3 m3…
Q: The beam consists of two S18 × 70 sections that are welded together as 15 kip/ft, calculate 5.70…
A: Given : wo = 15 kip/ft;
Q: 5. For a linear viscoelastic material, assume its = 3 seconds, T = 31 seconds, ER = 150 MPa, please…
A:
Q: In the figure, an aluminum wire, of length L₁ = 513 cm, cross-sectional area 5.00x102 cm², and…
A:
Q: In Buckling test: find Fc for the steel rod with dimensions (b-4.0 mm, h-2.0mm), its E =200 Mpa, and…
A: Given that, the rod is fixed E=200 MPa=200 N/mm2L=25 cm=750 mmb=4.0 mmh=2.0 mm The formula to…
Q: The table below shows ultimate tensile strengths (Fu ) and Young's moduli (Y) for tungsten (W) and…
A:
Q: (ii) If the velocity of sound in a solid is 3 x 103 m/s in which the interatomic distance is 3 x…
A:
Q: You are working in a factory that produces long bars of copper with a square cross section. In one…
A:
Q: Two particles are fixed to an x axis: particle 1 of charge q1 = 2.01 × 10*8 C at x = 17.0 cm and…
A: Given: Charge on particle 1,q1=2.01×10-8CCharge on particle 2,q2=-3.61q1=-3.61×2.01×10-8CDistance of…
Q: how was L calculated for from calcualtions shown
A: To determine how L was calculated from the given calculations, let's analyze the steps shown in the…
Q: Describe how longitudinal stability is achieved for Bell helicopters
A:
Q: A specimen of a 4340 steel alloy with a plane strain fracture toughness of 54.8 MPa is exposed to a…
A: Given:Fracture toughness,KIC=54.8 MpaParameter,Y=1.734 surface crack,a=0.4534 mm=0.4534×10-3…
Q: At what point the mull point will be obtained on a meter-bridge if the ratio of resistances im the…
A: We have to find: Position of null point We have given data from the question is: R1R2=23
Q: A fibre has a fatigue susceptibility parameter of n = 20 Develop an argument to show that a fibre…
A:
Q: A filter material has a porosity of 0.75 and the Filter Path length is 2 mm. The dia of individual…
A: Calculate the total Single fiber efficiency by the following equation. E=1-exp-2αEεhπ1-α rf…
Q: Compute the bulk modulus of water from the following data: Initial volume = 100.0 litre, Pressure…
A: We have, P=100 atmosphere…
Q: Polyethylene (HDPE) pipe is used as a strut in a crutch assembly. The pipe generally prepared by…
A:
Q: An FCC crystal is pulled in tension along the [100] direction (a) Determine the Schmid factor for…
A: Solution: Given that, An FCC crystal is pulled in tension along the [100] direction. Given…
Q: If you shine light with a wavelength of 153 nm on Potassium, what is the velocity of the electrons…
A:
Q: brass rod with a length of 1.40 m and a cross. sectional area of 2.00 square cm is fastened end to…
A: brass rod with a length of 1.40 m and a cross. sectional area of 2.00 square cm is fastened end to…
The critical angle of a medium for a specific wavelength, if the medium has relative permittivity 3 and relative permeability 4/3 for this wavelength, will be
Step by step
Solved in 2 steps