Thermodynamics: Please show me how to solve the given practice problems in step by step solution. 9. The COP (y) of a reversed Carnot cycle is 5.35 when refrigeration is done at 255 K;AS = 0.38 kJ/K during the isothermal heat interactions. Find (a) the refrigeration orcooling effect, (b) the temperature at which the heat is rejected, (c) the net work,

Answered: Image /qna-images/answer/ac9792af-1383-4a62-86d9-f75bec620e53.jpg

Answered: The COP (y) of a reversed Carnot cycle…

The COP (y) of a reversed Carnot cycle is 5.35 when refrigera AS D0.38 kJ/K during the isothermal heat interactions. Find ( cooling effect, (b) the temperature at which the heat is rejecte

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Steady state heat flow means, (a)Negligible flow of heat, (c)Heat flow independent of time (d)Uniform rate in temperature rise of a body 2. The ratio of heat flow QI/Q2 from two walls of same thickness having their thermal resistances as Rth1=8 Rth2 (b)No difference of temperature between the bodies will be: b) 0.25 3. The critical thickness of insulation for hot pipe is equal to: b) unity a) 0.125 c) 2 d) 4 a) h/k 4. Which of the following expresses thermal diffusivity of a substance in terms of thermal conductivity(k), density (p) and specific heat (C) a) (p2 k C) c) zero d) k/h d)(p C/k2) b) (1/ p k C) 5. The boundary condition of the end insulated fin are: c)(k/ p C) dT a) - kA() = 0 and T-To at x-0 b) - kA().- = 0 and T-Too at x=L dx d) None of them c) T=0 at x=0 and q=0 at x=L 6. The equation for the temperature profile inside a solid cylinder with heat source is: T-T a) T=T, + x b) =1-( !! 2k T,-T (R²-r) T-T = 2k c) d) None of them 7. Plane wall with heat generation, at x-0…
Your house has an electric water heater. Several friends are visiting you over the weekend and they are taking consecutive showers. Assume that at the maximum heating level, the heater uses 50 kW of electricity. The water use rate is a continuous 4 gallons per minute with the new water saving showerhead you recently installed. Your very old showerhead had used 7 gallons per minute. You replaced the showerhead because you learned that heating water was the second highest energy use in your home. By slowing the flow of water through the heater, the water temperature should increase to a higher temperature. (a) What is the change in temperature (T) for the old showerhead? (b) What is the change in temperature (T) for the new showerhead? Assume the system is at steady sate, and all of the 50 kW energy used is heating the water.
5.5
number 1 A food product containing 82% moisture content is being frozen. Estimate the specific heat of the product at -8 ° C when 82% of the water is frozen. The specific heat of the dry product is 2.5 kJ / (kg ° C). It is assumed that the specific heat of water at -10 ° C is the same as the specific heat of water at 0 ° C, and that the specific heat of ice follows the function Cp es = 0.0062 T Frozen + 2.0649. Cp of frozen product = kJ / kg ° C.
) Two boilers, one with superheater(B1) and other without superheater(B2) are delivering equal quantities of steam into a common main. The pressure in the boiler and main is 20 bars. The temperature of the steam from a boiler with a superheater is 350oC and temperature of the steam in the main is 250oC. The steam in B2 is wet steam at 20oC. i) Draw a sketch of the problem with all thermodynamic properties from steam table shown on the sketch. ii) Determine the quantity of steam supplied by the other boiler. Take the heat capacity of steam, Cps = 2.25KJ/Kg.hgas= hg + Cps (Tsap-Tsat)
A very convenient and compact method of representing the process dynamics of linear systems involves the use of _______ and block diagrams. _______ can be obtained by starting with a physical model. ( Note that the two _______ refer to the same term).
2) A rectangular membrane that is 0.5m by 0.75m has a displacement of 2 mm at it's center at time zero and a tension on each edge of 100 N/m, and mass per unit area of 1 kg/m2. What is the displacement after 0.5 seconds.
Q.2 The following data relates to the office air conditioning plant having maximum seating capacity of 25 occupants : Recirculated air Room Outside air 4) to = 34°C tm = 28°C ta2 = 24°C $2 = 50% Mixing Coil Outside design conditions: 34°C DBT, 28°C WBT Inside design conditions: 24°C DBT, 50% RH Solar heat gain= 9120 W Latent heat gain per occupant= 105w Sensible heat gain per occupant=90w Lightening load= 2300 W Sensible heat load from other sources= 11630 W Infiltration load= 14 m³/min Assuming 40% fresh air and 60% of recirculated air passing through the evaporator coil and the by-pass factor of 0.15. Draw the process on psychrometric chart and find the dew point temperature of the coil and capacity of the plant.
2. I just need the graph of this. A certain ideal gas (unknown) inside a close piston-cylinder assembly undergoes a set of processes that composed of Isothermal expansion from State point 1 to state point 2, Isometric heat rejection from state point 2 to state point 3, and Isentropic compression from state point 3 back to the initial condition. If the maximum pressure is 3000kPa and maximum and minimum volume is 200cm3 and 50cm3
Based on the first law of thermodynamics, which of the following is wrong? A the heat transfer equal the work plus energy change B the net heat transfer equals the net work of the cycle c) the heat transfer cannot exceed the work done D the net heat transfer equals the energy change if no work is done
design depends upon mathematical formulae of principle of mechanics. O a. Industrial O b. Optimum O C. Rational O d. Empirical