The control arm is subjected to the loading shown in Fig. 1–25a. Determine to the nearest in. the required diameters of the steel pins at A and C if the factor of safety for shear is F.S.= 1.5 and the failure shear stress is Ttail = 12 ksi. 3 kip FAB 8 in. Single shear 3 kip Pin at A 8 in. (c) Double shear 6.082 kip -3 in.- 2 in. - 5 kip 3.041 kip (a) 3 kip - 3 in.-2 in. 5 kip 3.041 kip C, 3 kip Pin at C (b) (d)

The control arm is subjected to the loading shown in Fig. 1–25a. Determine to the nearest in. the required diameters of the steel pins at A and C if the factor of safety for shear is F.S.= 1.5 and the failure shear stress is Ttail = 12 ksi. 3 kip FAB 8 in. Single shear 3 kip Pin at A 8 in. (c) Double shear 6.082 kip -3 in.- 2 in. - 5 kip 3.041 kip (a) 3 kip - 3 in.-2 in. 5 kip 3.041 kip C, 3 kip Pin at C (b) (d)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can this be done using simpsons rule?
Replace the loading by an equivalent resultant force. Suppose that w₁ = 2 kN/m and w₂ = 5.5 kN/m (Figure 1) Figure 4 m- نم -2 m 1 of 1 X
ANSWER FAST
Question 1 An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is 3 mm thick in SOLIDWORKS. The engineer most likely used the feature. Chamfer Fillet Hole Extrude
What is the Falling Block?
What is the sliding block?
Q/2 A/ Fill the Blanks. 1- Metals is more- -than ceramic in this property. 2- The engineering design deals with ---and - 3. Chemical reaction of a material with its environment can be considered failure by 4- prototype is- 5- Ductile fracture is characterized- -and- 6- The ---- is a material that characterize with change their shape when their temperature changes. 7- The product service life is expected to be shorter than anticipated in the design because of -----and - 8- The main characteristic of the ---- have electric properties that are combine between the conducting metallie materials and the insulating nonmetallic materials. 9- The one of the reasons for Development of existing products is---
What are the concentrated forces?
32. Fine-grained materials have stress-hardening properties. a. True b. False
Choose correct answer: When the cylinder is cushioned at the end of the stroke, how does cushioning affect the piston's force? At the beginning of the stroke, cushioning increases the piston's force. At the beginning of the stroke, cushioning reduces the piston's force. At the end of the stroke, cushioning increases the piston's force. At the end of the stroke, cushioning reduces the piston's force.
F P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.
Would the plank and the roller have the same acceleration why or why not?