The compound shaft shown in Fig. is attached to rigid supports. For the bro segment AB, the diameter is 75 mm, t ≤ 60 MPa, and G = 35 GPa. For the steel segment BC, the diameter is 50 mm, T ≤ 80 MPa, and G = 83 GPa. If a = 2 m and b = m, compute the maximum torque T that can be applied. A a B b C

The compound shaft shown in Fig. is attached to rigid supports. For the bro segment AB, the diameter is 75 mm, t ≤ 60 MPa, and G = 35 GPa. For the steel segment BC, the diameter is 50 mm, T ≤ 80 MPa, and G = 83 GPa. If a = 2 m and b = m, compute the maximum torque T that can be applied. A a B b C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution with clear calculations
Determine the magnitude of the pin force at A. Assume W = 535 lb, a = 4.6 ft, b = 3.5 ft, r = 9 in. r W C Answer: A = i a B a A D lb b
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F-2770 N, a-2.1m, b-4.2 m, 0 = 48% Answers: AB- AC- AD- BC- B CD i i i b 8 N N N N N
The compound shaft, which is fixed at both ends, is composed of Aluminum shaft ABC (Gal = 24 GPa, d = 50 mm), steel sleeve AB (Gst = 76 GPa, dout = 90 mm), and copper sleeve ABC (Gcu = 45 GPa, dout = 75 mm), which are all welded together. Considering the allowable shear stresses (Tal, Ist, Tcu), determine the maximum allowable torque T (kN-m) that may be applied at B as shown. Note: Double-headed arrows follow the direction of the thumb when using the right-hand rule. A Parameters Tal = 51 MPa Tst = 101 MPa Tcu = 71 MPa steel Cu AI L = 5m B ➡T Cu AI L= 3.5m C
The torsional assembly consists of solid 1.9 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 2.3 in. diameter bronze [G= 6,500 ksi] segment (2). Segment lengths are L₁ = L3 = 40 in. and L₂ = 58 in. Concentrated torques of TB = 2To and Tc = To are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 2.5°, determine: (a) the maximum magnitude of To that may be applied to the assembly. (b) the maximum shear stress magnitude in aluminum segments (1) and (3). (c) the maximum shear stress magnitude in bronze segment (2). y L₁ L2 2To L3 A (1) (2) N Answer: (a) To = (b) T₁ = T3 = (c) T₂ = B kip-in ksi ksi ksi C To D
answer only letters D and E
The change in diameter of the large steel bolt is carefully measured as the nut is tightened. Knowing that the initial diameter d = 50 mm, E = 190 GPa, and ? = 0.27, determine the internal force in the bolt if the diameter is observed to decrease by 0.009 mm after the nut has been tightened. Assume that the supports shown are fixed and rigid. d
Only ?% correct solution
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A A P1 L1 + Dia. 1 B B L2 Dia. 2 C L3 P2 30 mm o P3 Dia. 1 (mm) (mm) Dia. 2 P1 P2 P3 L1 L2 L3 (kN) (kN) (kN) (mm) (mm) (mm) 55 38 125 40 55 1000 1900 1000
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson
Need correct and well-explained solution. Please solve it correctly. Thank you.
DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 214 N %D F2 = 876 N %3D F3 = 435 N a = 38 degree X = 15 m. **Note: for compression, include a negative sign (- ) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. В H A C E G F1 F2 F3