The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. Bronze Steel 4.5 m *F120 mm -3,5 m / T

The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze. Bronze Steel 4.5 m *F120 mm -3,5 m / T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm. If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 1. A 200mm 250mm 3. 30 N-m 300mm 20 N-m 80 N m O 2.34MPA O 7.49MPA O 4.68MP O 3.74MPA
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
etermine the elongation of a 0.5-in, dianeter sterl bar The elastic modulus of the steel bar is 27000 kar. 2000 Ib 10 ft
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
The brass wire has a triangular cross section, 2mm on a side. The yield stress for brass is Ty= 208 MPa. Gbr= 37 GPa. Determine the maximum torque to which it can be subjected so that the wire will not yield and the angle of twist
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
For the shown Fig., find the maximum shearing stress in bronze part of the shaft. * Steel d= 200mm G= 80GPa Bronze d= 100mm d= 100mm G= 40GPa G= 30GPA 2KN.m Aluminum 8KN.m 3kN.m 3m 2m 1.5m +
The cantilever beam shown is an aluminum pipe that has an outside diameter of 114 mm and an inside diameter of 97.3 mm. A moment of 3 kN-m is applied at the free end. Find the rotation at the free end of the pipe. Neglect the weight of the pipe. М 33KN.m 2m Mod. of Mod. of Coeff, of Elasticity Rigidity G Thermal Ultimate Strength Density kg /m3 x 10 Tensile Yield Strength F, MPa Expansion a m/m/C x 10-6 Poisson's MPa MPa MPa Ratio Material x 10 x 10 Tens. Comp. Shear Steel ASTM A36 or A501 7.85 207 83 250 400 11.7 0.25 Steel (high-strength low-alloy) ASTM A992 7.85 207 83 345 450 11.7 0.25 Steel AISI 1020 hot-rolled 7.85 207 79.3 210 380 11.7 0.25 Steel AISI 1040 hot-rolled 7.85 207 79.3 290 520 11.7 0.25 Stainless steel 7.85 200 80 280 580 410 11.7 0.25 (annealed) Cast iron (gray) 7.21 103 41 140 550 220 10.6 0.26 Aluminum allov 2.64 70 28 240 260 190 23.6 0.33 6061-T6 Magnesium alloy 1.794 45 17 210 280 140 26.1 0.34 Titanium alloy 4.40 114 45 900 970 690 9.7 Nominal Outside Inside…
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.