The compound lever pruners shown in the figure can be adjusted by means of bolt A in various ratcheting positions on the ACE blade. Knowing that the length AB is 0.85 in, determine the forces exerted on each of the elements that make up the clippers. Make the required free-body diagram (s) of the elements and place the corresponding directions of the forces in each of the diagrams.

Q: The T-shaped structure is embedded in a concrete wall at A and subjected to the force F₁ and the…

A: The value of force is The moment is The dimension are The net resultant moment about A is

Q: Solve the following structure for the forces in member AB and draw and label a free-body-diagram for…

A: Given data, There is a structure in which a UDL of 1.5 lb/ft and a point load of 10 lb is applied.…

Q: 4. For the clamping wrench shown, calculate the force required to squeeze the handles together at…

A:

Q: 4. The frame system is loaded as shown. Support A is an anchored frictionless pin. Support E is a…

A:

Q: A lunch tray is being held in one hand, as the figure illustrates. The mass of the tray itself is…

A:

Q: 2. Using the method of sections (no other method is acceptable), determine the forces acting in…

A:

Q: Also determine the magnitude of the force in hydraulic cylinder AB. Express your answer in units of…

A:

Q: 4. The square plate is suspended by four cables that as shown. Tensile forces in AB and AC are 90…

A:

Q: The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB,…

A: A pin support will exert both horizontal and vertical components of reaction as the reaction forces.…

Q: The following forces are acting on the bracket below (a free-body diagram of the bracket is shown),…

A: Solution:

Q: A person pulls on a 500 N desk with a 200 N force acting at 30° angle above the horizontal. The desk…

A: QuestionA person pulls on a 500 N desk with a 200 N force acting at 30° angle above the horizontal.…

Q: The boom ABC in Fig 4 is held by the ball and socket joint at A and the two cables EBF and CD, as…

A:

Q: 1.6. Find the horizontal and vertical components of the forces at all jointa. The reaction at point…

A:

Q: he given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively,…

A: Find the internal force in members and percentage error.

Q: A construction worker on a job site attempts to move a boulder out of the way by attempting to apply…

A: First, we know a total of "F1 "and "F2 "is equal to "F" and after that, we take a moment about point…

Q: Replace the loading shown by a single equivalent force. Specify the magnitude and direction of this…

A:

Q: The truss shown is supported by a roller at A and a pin at H. Calculate the reactions at these…

A:

Q: 360 mm 840 mm 852 mm 132 mm 732 Mm X 1200 Mm The lid ABCD of a storage bin is hinged AB and is held…

A:

Q: Consider the clamping device used to lift a 55 gallon drum, as depicted in the accompanying figure,…

A:

Q: The crate weighs 6.5lb and is supported by stick BC. Find the magnitude and direction of the…

A:

Q: 4.26 The homogeneous bar AB weighs 25 Ib. Determine the magnitudes of the forces acting on the bar…

A: Given: Weight of bar = 25 lb Friction neglected.

Q: Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.56-lb force about…

A:

Q: We make a cut through BC, BF, and FG. The free-body diagram of the section to the left of the cut is…

A: To Find : Determine the force in BF  and θ . Given : F1=7.3 kipsF2=3 kips

Q: The T-shaped structure is embedded in a concrete wall at A and subjected to the force and the…

A: The value of force is The moment is The dimension are The net resultant moment about A is

Q: A homogeneous rod AB weighs 100 N. The end is attached to the wall with hinges, while the B end is…

A: Given Beam weight = 100 NDead weight = 200N To find Free body diagram Tension in rope BC

Q: Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.50-lb force about…

A: Moment of force about any arbitrary point is equal to the product of magnitude of force and the…

Q: 45° C d

A: GIVEN:

Q: A 2.0 long bar is being used as a first-class leaver. It has a load of 720 N placed on one end…

A: Given data: The length of the bar is l=2 m. The load acting on the body is FC=720 N

Q: please compute a force analysis of both the slender bar AB connected to the string and -he cylinder

A:

Q: Q3: Answer One of the following: (10 Marks) A: for the frame shown below, calculate the components…

A: Given data: The angle ∠ABC = 45o Consider the value of B = 30o Also, B+∠ACB = 90o ∠ACB = 60o Now…

Q: B↓ 1 ft TA 1 ft A 40% 40° D Mc P B 15° C

A:

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

A:

Q: This question is already answered The answer was really good. My doubt is that ,Why there is no…

A:

Q: 3. A 60 pound force is attached to the 90° weightless bar ABCD at point B as shown below. The bar is…

A:

Q: A 392-N force parallel to the plane is required to support a body on an inclined plane, of height…

A: Given data: Support force applied to the body, P = 392 N. Normal force acting on the body, N = 780…

Q: Determine the forces in AB and BC and indicate the direction of each.

A:

Q: Assuming clockwise moments as positive, determine the moments of the forces shown about the…

A:

Q: For the loading system shown on the beam below, calculate the reactions at the two supports. ITT 500…

A:

Q: , hinged at A and D and pinned at B and C as sho a. Determine the value of P that will prevent…

A:

Q: Using the method of sections, determine the magnitude of the forces: a) the reaction force at…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.