The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 35 mm, an inside diameter of 25 mm, and a shear modulus of G1 = 44 GPa. The solid steel core has a diameter of 25 mm and a shear modulus of G2 = 82 GPa. Assume L = 530 mm. The composite shaft is subjected to a torque of T = 740 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. T T (1) (2) B Answers: (a) T1 = MPa T2 = MPa (b) PBIA = rad

The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 35 mm, an inside diameter of 25 mm, and a shear modulus of G1 = 44 GPa. The solid steel core has a diameter of 25 mm and a shear modulus of G2 = 82 GPa. Assume L = 530 mm. The composite shaft is subjected to a torque of T = 740 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. T T (1) (2) B Answers: (a) T1 = MPa T2 = MPa (b) PBIA = rad

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Formulate the equation of angle of twist at end C with respect to A in terms of T
Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T0 = 10 kN.m is applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm.
The cross-sectional view of a closed section, thin-walled tube is shown in the figure. The thickness of the segments AB and BC is 4mm while it is 6mm forthe segments CD, DE and EA. If the tube material is Al 2014-T6 aluminum alloy, calculate the maximum torque value that can be applied safely on the cross-section. A E 200 80 B mm T mm D 200 mm 400 mm
A compound shaft consists of an aluminum tube (1) securely jointed to a steel tube (2). Both aluminum and steel tubes have an outside diameter of D= 48 mm and a wall thickness of t= 3 mm. The shaft is secured by a fixed support at one end and is subjected to a torque of T= 115 N.m at the other end. Determine the maximum stress in the shaft.[L1 = 200 mm, L2 = 350 mm, D = 48 mm , t = 3 mm, G = 75 GPa]
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 3730 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.5-m length of shaft. 0.0807 rad 0.1091 rad 0.0556 rad 0.0861 rad 0.1009 rad
The problem is stated below. However, change the position of torque to point C from point D. What is the effect of variation of torque placement in shaft CB?
The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Answers: (a) T₁ = (b) P DIA Nc WWAMACOM Save for Later C 9.3808 = i 2.1378 e Textbook and Media NB L₁ B D TD ksi, 1₂: = i 14.5924 ksi. Attempts: 1 of 5 used Submit Answer
No gpt, 1ly handwritten
The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the angle of twist developed at the interface of the two segments when the torque T = 50 kip٠in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel.
The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. Gst = 10.8(10³) ksi. (Figure 1) Figure sin. A 0.5 in. Jc 8 in D 500 lb-ft 12 in. 1 in. B < 1 of 1 Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μÅ Value 6 Request Answer Units www. ?
Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at 'J. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA 600 mm 75mm 600 mm 50mm 800mm G. T2
The compound shaft is attached to a rigid wall at each end and is subjected to the torque T = 10 kN.m applied at point B. For the bronze segment AB, the diameter is di = 79 mm and Gbr = 35 GPa. For the steel segment BC, the diameter is d2 = 44 mm and Gt = 83 GPa. Given that a = 2.5 m and b = 1.8 m, what is the torque reaction TA developed at end A? dz Bronze Steel