The composite beam loaded with a triangular distributed load , consists of two aluminum alloy beams with elastic modulus EAI= 70 GPa that are bonded to a wood beam with elastic modulus Ew= 12 GPa. The design requires that the magnitude of the beams maximum deflection at the free end be not greater than (first two numbers of your student number) mm. What is the largest value of mo for which yielding of either material will not occur. 25mm wood Aluminum 100mm 25mm 50mm B. 100mm

Q: In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e = 7 cm. Find the value of angle a…

A:

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: (degree) Calculate the measure of the angle in degrees marked in white for the following figure 24…

A:

Q: Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular…

A: Given: To find: Write a program to drill holes and mill

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: I'm playing a game of pool with by brother; he's stripes. At some point, I notice I have a…

A: V = 6 oz = 0.17 gd = 2.25 inches = 0.057 me = 0.95  "coefficient of restitution" "coefficient of…

Q: Question The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall…

A:

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: 4. Determine the pressure difference between the points at A and B. Take the density of air as…

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: The piston displacement of an air compressor is 1200 liters per minute. Its bore and stroke are 12…

A:

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: Please show the computation in solving for NB and FAB

A:

Q: Find the limit. NOTE: Enter an exact limit if it erists. If the limit does not exist, indicate that…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: For the laser cutting of the shown path, determine the absolute and incremental coordinates of the…

A: given; findabsolute and incremental co-ordinate;

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: Calculate DOF. Please solve Carefully asap

A: Given:- mechanism with four link Determine:- Degree of freedom (DOF)

Q: From the figure shown. To determine: a) Piston force BC b) Piston force FE c) Pin force G and J d)…

A: Consider the free body diagram of bucket is shown below, Taking moment about point J, ∑MJ=020000…

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: An automobile tire is 65.0 cm in diameter. How fast (rpm) does the wheel turn on the axle when the…

A:

Q: Q4 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 1:1.

A: Required Front view, Top view and side view are drawn using first angle method of projections.

Q: b) Calculate the inclined angle λ and orthogonal rake angle yo, when yx =10°, yy =8°, ps=15°.

A:

Q: o shafts 3679mm between centers carry pulleys 1288 mm in diameter and 910 mm in  diameter…

A: dL= diameter of larger pulley dS= diameter of smaller pulley C= distance between the centers of…

Q: Completely solve and box the final answers. Write legibly 5. How much twisting moment in lbf-ft is…

A:

Q: Finish the Orthographic drawing

A: Please refer the following Front view, right hand side view and top of the given isometric view. 1…

Q: A piston engine in which the bore and stroke are of equal dimension is referred to as a "square…

A: Given:Let bore be 'D' and stroke be 'L'For a square engine, D = LNo of cylinders, n = 8Displacement…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.