The composite area should in Figure 1 is composed a triangle JKL and a rectangle KLMN with a circular void with its centre at C1. la) Calculate the moment of inertia of the composite area shown in Figure 1 with respect to x- axis (L). Locate the centroid, C of the composite area shown in Figure 1, with respect to x & y coordination system. Hence calculate its moment of inertia with respect to its centroidal x'-axis (I). Calculate moment of inertia of the composite area shown in Figure 1 to x1-axis (Ii) and X7-axis (I2). 1b) 1c) y N X2 K b mm r mm J h mm M X1 L a mm b mm Figure 1

The composite area should in Figure 1 is composed a triangle JKL and a rectangle KLMN with a circular void with its centre at C1. la) Calculate the moment of inertia of the composite area shown in Figure 1 with respect to x- axis (L). Locate the centroid, C of the composite area shown in Figure 1, with respect to x & y coordination system. Hence calculate its moment of inertia with respect to its centroidal x'-axis (I). Calculate moment of inertia of the composite area shown in Figure 1 to x1-axis (Ii) and X7-axis (I2). 1b) 1c) y N X2 K b mm r mm J h mm M X1 L a mm b mm Figure 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An embankment is to be constructed by making use of sandy clay having the following properties: c' = 35 kN/m2, o' = 25° and y= 19.5 kN/m3. The height of the embankment is 20 m with a slope of 30° with the horizontal as shown in below figure. Estimate the factor of safety by the method of slices for the trial circle shown in the figure. 35 25 m- e- 35 ENm 20 m O'= 25° 25 y= 19.5 kN/m 30
Q#3. Draw Shear Force and Bending Moment Diagram Graphically for the following Вeam. P=20KN q=5kN/m A, 5m 5m 4m
As seen in the figure, the block on an inclined plane is lifting from 0 0 with two degrees increment in each step. (0, = 0, 0 =2, 02 = 4, ..) Until which degree can we increase the angle without any slipping between the block and the inclined plane? For condition of F > F, the block continues to hang on the inclined plane. Otherwise, it starts to slip. F, = W + sin8(rad), Fy = W+ cosa(rad) F = F, + u, u = 0.50, W = 100 N
Question 6 For the loaded beam shown in Figure Q6 below, consider section M-M and determine the following: 6.1 The maximum shear stress in that section 6.2 The shearing stress at point P 12 mm 25 kN 20 jN M M B 12 mm 00 mm 0.4m 0.3 m 0.4 m 00 mm Figure 06: Loaded beam
Parvinbhai
In the figure, the machine element located at the C point in the transmission system is radial and axial loads. These loads; Fr: 500 daN, Fa = 250 daN in addition to this .Testing the load of the machine element affects the spindle once again up to 100 daN. Loads in the system A and B are covered by a single row ball bearing. By evaluating what is given; a-) Calculate the forces acting on the bearings and the required shaft diameter. b-) Choose the most optimum bearing so that the life of the A bearing will be at least 4000 hours. For the shaft material in the system; oem = 7 daN/mm2, bearings will operate with 1000 rpm rotation speed. Important Note: Axial Load will be carried by the A-bearing Fa Fr A В 200mm 180mm 220mm
Find the shear force and bending moment at points C and D. 60 lb/ft Answer: VD= 637 lb (up) Mp= = 3185 lb ft (ccw) Vc = 559 lb (up) Mc = 3033 lb ft (cw) -10 ft- -15 ft- 40 lb/ft B B ID -5 ft- -10 ft- 690 Ib 13 12 A
Shaft 2a cos 0 R Groove Figure P7-5.5 Compute tmax in terms of M and a for a = 60°, a = 45°, and a = 30° (Fig. P7-5.5). Compute t at the point P for these cases. Verify that trz = tyz = 0 for corners A and B. U%3D
A lifeboat hangs from two ship’s davits, as shown in the figure. A pin of diameter d = 0.8 in. passes through each davit and supports two pulleys, one on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a αα = 15∘∘ with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that should be carried in the lifeboat?
Please draw shear force diagram v(X) and bending moment diagram m(X)
pls very urgent
In the figure, the bending stress equal, if the moment inertia 5m ^ 4 and the perpendicular distance is 3m.