The components of a Steam Power Plant in correct order are Evaporator, Condenser, Boiler, turbine Boiler, Turbine, Condenser, Pump Boiler, Turbine, Evaporator, Pump

Q: Expandable pattern is used in ?

A:

Q: What is a piece of 1/2" x 1" x 10' long stock commonly called?

A: Given:-  What is a piece of 1/2" x 1" x 10' long stock commonly called?

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: What does it mean to be an independent slip system?

A: Slip system: It is a combination of slip planes along which the probability of deformation is…

Q: I have three parts that need to be answered pertaining to the print provided below.   What size…

A: The size of the print provided in the title box is C.Hence the correct answer is C.

Q: How can the angle of twist of one end of a shaft or tube with respect to theother ends be…

A: Given Data: The length of the shaft is L. The diameter of the shaft is d. The moment acting on the…

Q: Solidworks. Units are IPS. 24 threads per inch. Primarily just need help designing the threads after…

A: It is asked to draw thread by using Solidworks software

Q: Why would engineers use Vickers Hardness testing (HV) over Brinell Testing for hardened tool steel…

A: Hardness is the property of the material that can be understand as the resistance to scratch and…

Q: This a sketch of what process. V, F Punch Flash Die Cutting edges Select one: a. Cutting O b.…

A: The given sketch represents Trimming process. Trimming process: The shearing of the excess material…

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: By what means kind of small area or stripe be selectively hardened and a large steel pa

A: induction hardening and flame hardening

Q: ne or more can be correct please select from below options  Lower operating temperatures are more…

A: In the moulding process known as compression moulding, a feeding material is inserted into an…

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

A:

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: enumerate the 4 plate forming process and where it can be applied

A: given; enumerate the 4 plate forming process and where it can be applied.

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: The 2XXX, 6XXX, and 7XXX series of raw aluminum alloy's or non-heat treatable and the 1XXX, 3XXX,…

A: Given: The 2XXX, 6XXX, and 7XXX series of raw aluminum alloy's or non-heat treatable and the 1XXX,…

Q: How were the areas for part 2 found?

A: Given Data and to find: How the areas are calculated?

Q: Describe the method of sections?

A: Method of section In this method we deal with the non-concurrent forces. Here, we get three…

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: True O False

A:

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in..     7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: Note 1 indicates 10 GAGE 1010-1020 sheet metal can be used to make the main body of this part…

A: Tolerance is the difference between the maximum size and the minimum size of the part or element.

Q: In the hardness test, answer the questions 1- What happens to the sample if its thickness is less…

A: Thickness of the specimen should be at least seven times of the depth of the indentation. It allows…

Q: What makes new gear special?

A: Given data:- Gear:-A gear is a mechanical device that connects two rotating shafts by transmitting…

Q: the main diference between the prick punch and center punch?

A: Prick punch is a mechanical tool, which is made up of steel and it is used to mark points on the…

Q: Which tool steel group would be the best for master gauges? D M P S

A: Given :-  Which tool steel group would be the best for master gauges? D M P S

Q: Pitch characteristics

A: pitch characteristic When viewed in a cross-sectional plane containing the axis of the thread, the…

Q: Sketch and explain any four Shaper operations?

A: The four shaper operations are, Horizontal cutting: It's one of the most popular operations on a…

Q: List and briefly describe the three types of tolerances used on prints.

A: Tolerance is important to factor that will be used to identify the machined or the manufactured…

Q: Statement: Torque is considered as negative if the right hand thumb direct outward from the shaft…

A: A propeller is said to have negative torque when conditions are such that, instead of the engine…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.