The component values in the passive filter circuit shown below are: C=10µF, L=1H, andR=10k2.+CVoutina. Derive an expression for the voltage transfer function, Vaue/V -expressions for the magnitude and the phase angle of that transfer function.Also, determineb. Classify the filter as LP, HP, BP or BS, and explain your reasoning.

Answered: Image /qna-images/answer/2bfbb6a2-c5a1-47db-9b51-3aff9c8f1618.jpg

The component values in the passive filter circuit shown below are: C=10¼F, L=1H, and R=10k2. Vin L out a. Derive an expression for the voltage transfer function, Vm/Vm. Also, determine expressions for the magnitude and the phase angle of that transfer function. ouf b. Classify the filter as LP, HP, BP or BS, and explain your reasoning.

The component values in the passive filter circuit shown below are: C=10¼F, L=1H, and R=10k2. Vin L out a. Derive an expression for the voltage transfer function, Vm/Vm. Also, determine expressions for the magnitude and the phase angle of that transfer function. ouf b. Classify the filter as LP, HP, BP or BS, and explain your reasoning.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I want the answer in detail and as quickly as possible please Q/ Using capacitors and resistors, design A - (band-pass filters) with Fl=105HZ and Fh=115HZ. B - Design (band-pass filters) with FI = 215HZ and Fh = 225HZ.
Using the series RLC circuit, yield a band reject filter with a bandwidth of 240 Hz and a center frequency of 740 Hz. Use a 100 nF capacitor. The value of w2 is
Find the transfer function for the circuit shown in the figure. Plot the amplitude graph of 2log10[H(jw)] and the phase angle graph of H(jw) Calculate the actual cutoff frequency? Calculate the true phase angle at the cutoff frequency?
Need Hand Drawn Please
(c) i. Draw the electronic circuit for a 1st order passive low pass filter,ii. Derive the transfer functions Vout/Vin in terms of capacitor C, resistor R and frequency fofthe low pass filter.iii. Draw the electronic circuit for a bandpass filter,iv. Sketch the bode plot showing the cut-off frequencies ofthe bandpass filter
Im + Re -100 -1 Figure 1: We want to sketch the bode plot for this filter! 1) Rewrite H(s) in the "standard form" for Bode plots 2) Using paper + pencil, sketch the Bode magnitude and phase shift plots. 3) What kind of filter is this: Low-pass Bandpass High-pass Notch
None
4. Given the following LRC circuit below: The circuit shown has a resonant frequency, fr=100 kHz. The circuit has a resistance value, R = 10002, capacitance value, C = 1.33nF. and an inductance value of L=1.904mH. a. Determine the quality factor, Q, for the circuit b. What is the BW of this circuit? c. Calculate the upper and lower cut-off frequencies. d. If the following triangle wave with a fundamental frequency, f, of 20 kHz is put through this filter, determine the output.
3. a) b) Write a short note on Nyquist Rate. Calculate the Nyquist rate in rad/sec and in Hz for, m(t) = 2 sinАnt · cosВnt
Ex. 1340. Refer to Figure setH(1340). Given: w1=1 rad/sec and G(s) = 34/s. Determine asymptotic (also actual): G1,G2,Ph1, mc where gains are in dB, frequencies are in rad/sec, and phases are in degrees. mc=Bode Plot type code. ans:4
Homework 5 1. In the circuit below, C=10 nF, and R=10 kOhm. A. Find the corner frequency (fc) in the circuit below. B. Write the Transfer Function, TF= Vout/VIN using the voltage divider equation. C. Find the magnitude and the phase of the TF at the frequency values of 0 Hz, fc, and infinity. Is this a low-pass or a high-pass filter? + VIN(1) C www VOUT(1)
Q2 Sketch the asymptotes of the Bode plot magnitude and phase for the controlled transfer function of the system described in the figure, calculate the gain and phase: margins, Take K = 1. d42u42 S+