Answered: The characteristic equation of a…

The characteristic equation of a control system is represented by: s* + 2s3 + 3s2 + 4s + K = 0 Use the Routh-Hurwitz stability criterion to find the range of K values for which the system is stable.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.18P

See similar textbooks

Related questions

Q: #2 A discrete time linear system has the responses y,[n], yz[n] and y3[n] as a result of the applied…

A: For linear system, we can apply law of additivity and superposition.

Q: b. A second order system settles to a final position in a time of 1.4 seconds in response to a unit…

A: Solution of question (b): Given information about a second order system is the system settles to…

Q: Q1: A sequential network has one input (X) and two outputs (Z₁ and Z2). An output Z1 Z2= 10 occurs…

Q: RL Circuits• Calculate the current in an RL circuit after a specified number of characteristic time…

A: Current in an RL circuit after a specified number of characteristic time steps. Current in a…

Q: transfer function of 2/ 8. Figure 9.30 shows an electrical circuit and its block diagram…

A: 8.Answer; given that a RC circuit and its block diagram To find the overall transfer function of…

Q: Q2 Consider the following characteristic equation s³ +25¹ +35³ +6s²-4s-8=0 Using the Routh stability…

A: In this question we need to check the system stability by using Routh stability criteria.

Q: 1. Find the state equations and output equation for a parallel R L C circuit driven by a current…

Q: A possible solution for a first and second order derivatives have the same form expressed as a. At?…

Q: Find the control ratio, C(s)/R(s) for the system given below using Mason’s Rule.

A: In this question We need to determine the tranfer function using the Mason gain formula. We know…

Q: 11. Which of the following circuits 12. Which of the following circuits I have the largest…

A: Need to identify which circuit has largest equivalent capacitance, total charge stored and voltage…

Q: One of the following statements is TRUE? O Methods based on Transfer Function Method are not always…

A: Transfer function method:- This method is used for estimate cooling loads and this loads are from…

Q: 1. Obtain the state diagram and a primitive flow table for a circuit with two inputs X1 and X2 and…

Q: 1. The switch in the circuit in Figure 1 has been in position a for long time. At t=0, the switch…

A: Given circuit-

Q: Q1: i. Define and explain the following terms with appropriate examples and graphs. a. Sensitivity…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: You are requested to design an automotive suspension or shock absorber system. In order to simplify…

A: The value of the system components are M1=2500kg,M2=320kg,K1=80000 Nm,K2=500000 Nm,B=350 N-sm.

Q: 1. Are the systems whose input-output relationship is given as below linear? Is it memoryless? Is it…

A: According to the question,

Question

100%

The characteristic equation of a control system is represented by:
s* + 2s3 + 3s2 + 4s + K = 0
Use the Routh-Hurwitz stability criterion to find the range of K values for
which the system is stable.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the general solution of the second order, inhomogeneous linear differential equation given below with the "Change of Parameters" method.
20 What is countertorque a measure of? PRACTICAL APPLICATIONS ou are working as an electrician in a large steel manufacturing plant, and Y in the of doing preventive maintenance on a large DC you are generator. You have megged both the series and shunt field windings and found that each has over 10 M2 to ground. Your ohmmeter, however, indicates a resistance of 1.5 2 across terminals S, and S,. The ohmmeter indicates a resistance of 225 N between terminals F, and F2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer. process
Discuss the pressure response in figure I after using the PID controller in tems of the Rise Time, Steady State Error, Settling Time, and Overshoot. Pressure vs Time Setpoint Actual 1532 26 15:1241 15:256 Time ARKR ES (ed)
Reference 7 segment display: Solve for the segments: "d, e, and f." Show your work 1. KMAPs 2. Reduced equation to lite up the segment 3. Describe the operation of Lab 12 4. If you were to add a 4th seven-segment, Describe your design process.
4. Which of the following is a mathematically incorrect operation and why? a) gradient of a divergence b) curl of a gradient c) gradient of a curl d) divergence of a curl
Control Systems Write the state equations of the circuit shown in the figure. Obtain the Vout expression for the values of C=2F and L=3H for R=5 ohms. Obtain the Vout(t) expression by using the sum of residues method when the input voltage is a unit-step function. Comment on the stability of the system. Note:Please explain and explain in detail.
What is linear time invariant system and their properties?
The definition of the nexus is given by the equation and the graph of the tip given in the figure. Obtain the Thevenin equivalent of the 2-tuple a-b containing this 3-nucleus.
Q3) Select the write choice and prove your choice theoretically. 1-The number of turns of a shunt field coil worked at a current density of 3 A/mm2 is - (if the coil resistance 80 ohm and develop 1500AT with an applied voltage of 60 V). a-2000 b-200 c-20
Subject name: Electrical Power Distribution.
Q2. Perform the following subtraction using l's and 2's complement method (Show step by step process) (i) (11010)2 – (10100)2 (ii) (1000101)2 – (1010100)2
I need the answer as soon as possible