The center of mass of a composite body: Is calculated as the sum of the product of the mass of each figure involved in the composite body divided by the total mass of the object. Requires integration for its calculation in all cases. Is calculated as the sum of the mass of each figure involved in the composite body multiplied by the distance of the centroid of that figure from a coordinate axis established on the object. Is the same as the center of gravity of the composite object.

The center of mass of a composite body: Is calculated as the sum of the product of the mass of each figure involved in the composite body divided by the total mass of the object. Requires integration for its calculation in all cases. Is calculated as the sum of the mass of each figure involved in the composite body multiplied by the distance of the centroid of that figure from a coordinate axis established on the object. Is the same as the center of gravity of the composite object.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
As seen in the figure, a rigid beam carried by three elastic rods of equal length from points A, B, and C is pulled to Eve from points F by P-force. The modulus of elasticity of the bars are E1=100GPa, E2=120GPa and E3=100GPa. Yield stress σA=40 MPa for bar 1 and 3, yield stress σA=120 MPa for bar number 2. Accordingly, a) determine the load PA that will start the flow, b) the load PG that will cause the migration.
There is no force on a beam, but the beam is subjected to a very large temperature difference above and below. As shown in the figure below, try to calculate the vertical displacement of the midpoint of the beam, assuming that the temperature coefficient of the entire beam is a = 11.7×10^-6 °F. Tip: See Mechanics of Materials for Beam Deformation Geometry
A metal ring as shown in Figure 4 is subjected to three forces 2C, 4C, and 8C respectively. Solve for the resultant force acting on the ring and the angle it makes with the positive x-axis. Note: C represents class number whivh is equal to = 4740.
Assuming that the members of the truss shown in the figure are deformable and are only subjected to tension and compression. Which among the members attached at joint B will shorten when the external loads are applied? 4 m E 5 m C 4 m B 4 m 80,000 N 60,000 N
The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain. Determine the strain components En, Et, and Ynt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle O. Sketch the deformed shape of the element. Ex = -850 UE, Ey = 310 UE, Vxy = 1050 urad, and 0 = 39°.
The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain. Determine the strain components εn, εt, and γnt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle θ. Sketch the deformed shape of the element. εx = -1200 με, εy = 240 με, γxy = 1350 μrad, and θ = 36°.
Aluminum [E = 72 GPa] member ABC supports a load of 31 kN, as shown in the figure. Determine (a) the value of load P such that the deflection of joint C is zero. (b) the corresponding deflection of joint B (positive if B moves up and negative if down). 1.0 m 1.3 m 31 KN C 34-mm diameter B 52-mm diameter
Assuming a rectangular simply supported beam loaded as shown in Figure and the height of the beam is fixed by other design considerations, determine the difference in width required for an aluminum beam compared to a steel beam.