The car bumper is made of polycarbonate-polybutylene terephthalate. If E = 2.0 GPa, determine the maximum deflection and maximum stress in the bumper if it strikes the rigid post when the car is coasting at v = 0.75 m>s. The car has a mass of 1.80 Mg, and the bumper can be considered simplysupported on two spring supports connected to the rigid frame of the car. For the bumper take I = 300(106) mm4, c = 75 mm, sY = 30 MPa and k = 1.5 MN>m.

Q: If m = 30 kg and assuming rough surfaces, draw the free-body diagram. Cable A 0.1 m В 30°

A: Answer:  tension in the cable = 169.914 NFor a step-by-step solution have a look through the…

Q: Assuming that the foundation exerts a linearly varying load distribution on its bottom, determine…

A:

Q: *8-60. Each block has a weight of 400 lb. Determine how far the force P can compress the spring…

A: To find: The compression of spring and force required. Given: The weight of each block isW=400 lb.…

Q: ww os 240 mm

A: A vector is a physical quantity that has magnitude and direction both. A scalar is a physical…

Q: Use the method of sections to determine the force in members DE, EI, FI, and HI of the truss State…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 8-50. The crate has a weight of 200 lb and a center of gravity at G. Determine the heighth of the…

A: Given weight of the crate w = 200 lb coefficient of friction μ = 0.4 To find? height h so that the…

Q: The collar has a weight of 50 lb and falls down the titanium bar. If the bar has a diameter of 0.5…

A: Write the formula for static deflection of the given load i.e. the weight of the collar. Here, P is…

Q: Determine the mass of each of the two cylinders if they cause a sag of s=0.5 m when suspended from…

A: Take the left side of the given figure and construct the left part.Note: When cylinders are…

Q: For the structure and loading shown below, determine the vertical and horizontal deflections and the…

A:

Q: A six-pack is shaken so that the pressure in each can is p = 20 psi. A board is placed on the six…

A: Write the given information.

Q: The uniform beam has a mass of 57 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: Determine the mass of each of the two cylinders if they cause a sag of s=0.5m  when suspended from…

A:

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: To determine the magnitude of the horizontal force  P  such that  xB​=5  meters, follow these…

Q: The 20 kg block is supported by two springs having the stiffness shown. Determine the stretch of…

A: From the above given data we have to find change in length for AB.

Q: tokN 6m 100KN TTT 4m 6M

A: Given: A truss is subjected to a loading as shown in the given figure. Determine: Determine…

Q: The collar has a mass of 5 kg and falls down the titanium Ti-6A1-4V bar. If the bar has a diameter…

A:

Q: Determine the reaction (kN) at B and E. NOTE: CHOOSE TWO (2) ANSWERS ONLY! 60 kN 40 kN/m 120 kN • m…

A:

Q: 6 kN/m A -3 m 6 m- B

A: given; lets take vertical reaction force at A=RAVlets take vertical reaction force at B=RBVlets take…

Q: The uniform beam has a mass of 46 kg per meter of length. Determine the reactions at the supports. a

A:

Q: Solve the forces at the spring and cable AB in equilibrium. Also, determine the stretched length of…

A:

Q: The car bumper is made of polycarbonate-polybutylene terephthalate. If E = 2.0 GPa, determine the…

A: Given data: Modulus of elasticity, E = 2 GPa. The velocity of the car, v = 0.75 m/s. The mass of…

Q: The 20 kg block is supported by two springs having the stiffness shown. Determine the stretch of…

A:

Q: The uniform beam has a mass of 40 kg per meter of length. Determine the reactions at the supports. A…

A:

Q: The 20 kg block D is dropped from a height h onto the steel beam AB. Additional data are: h= 500 mm…

A: When a mass 'm' falls at a height 'h' on the beam, deflection produced in the beam is known as…

Q: The horizontal steel shaft has a mass of 475 kg and is suspended by a vertical cable from A and by a…

A:

Q: When the 100-lb block is at h = 3 ft above the cylindrical post and spring assembly, it has a speed…

A: Above loading is Type of impact loading. In impact loading , stress generated in the body is higher…

Q: The pipe can be assumed roller supported at its ends and by a rigid saddle C at its center. The…

A: Free-body diagram of a pipe is given as, On using equilibrium of force in a vertical direction,…

Q: The A-36 steel bolt is required to absorb the energy of a 2-kg mass that falls h = 30 mm. If the…

A:

Q: A circular beam with a diameter of 25.4 mm is subjected to the applied forces and is fixed at…

A: Given:The diameter of the circular beam,

Q: The beam is loaded with a uniformly varying load 0 at point D and maximum of 7 kN/m at the fixed…

A:

Q: . Determine the support reactions and internal forces N, V, and M that occur midway between supports…

A:

Q: 3L/4 P The beam shown is fixed at the left end and is supported by a pin at the right end. Using any…

A:

Q: The beam is loaded with a uniformly varying load 0 at point D and maximum of 7 kN/m at the fixed…

A: Given data: w=7 kN/m Need to determine the horizontal reaction force at the support.

Q: 1- Determine the force developed in the member BC and reactions at the pin support A. Take Gi = 5Kg.

A: Given data Mass (G1) = 5kg

Q: The beam is loaded with a uniformly varying load 0 at point D and maximum of 7 kN/m at the fixed…

A:

Q: The 100 kg block is supported by two springs having the stiffness shown. Determine the stretch of…

A:

Q: The composite aluminum 2014-T6 bar is made from two segments having diameters of 7.5 mm and 15 mm.…

A: Given data d1=7.5 mmd2=15 mmσmax=300 MPaσy=410 MPaE=70 GPa

Q: The 80 kg block hits the simply supported beam of steel at its midspan after a drop of 10 mm as…

A: Given, m=80kgLoad , W=mgW=80×9.81W=784.8N RA=RB=W2RA=RB=392.4NMoment at…

Q: Take E=240 GPa and I=75(10-6) m² A 10 kN/m 6 m. -6 m. Determine the reaction at the roller support B…

A: Step 1: Step 2:Step 3: Step 4:

Q: The beam is subjected to the two concentrated loads. Assuming that the foundation exerts a linearly…

A:

Q: A -2m- W 2 m- B 1m'1m P - -Q Find rb(reaction) What is the magnitude and direction of the reaction…

A: Calculated the magnitude and direction of the reaction at A.

Q: Determine the ratio of support reaction Ra/Rc

A: Given data : Point load P1=12 KNP2=8 KNTo find :Ratio of support reaction

Q: The frame consists of members ABC and DEF, and links BF and CE that connect the two members. The…

A:

Q: The composite aluminum 2014-T6 bar is made from two segments having diameters of 7.5 mm and 15 mm.…

A: Given: D1= 7.5 mm D2=15 mm m= 10 kg h=100 mm To determine: maximum axial stress developed in the bar

Q: The 30-kg block is supported by two springs having the stiffness shown. Determine the unstretched…

A:

Q: 6] Determine the required length of cord AC in Fig.below so that the 8-kg lamp can be suspended in…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.