The car acceleration takes the form du/dt = 1.2 -0.06u where u is the vehicle speed in meter per seconds. The vehicle is traveling at 14 meter per seconds at the initial time. Find the following: 1. Time at which the car attains a speed of 20 meter per seconds. 2. Acceleration of the vehicle after 5 sec 3. Distance traveled by the vehicle when accelerated to a speed of 20 meter per seconds.

The car acceleration takes the form du/dt = 1.2 -0.06u where u is the vehicle speed in meter per seconds. The vehicle is traveling at 14 meter per seconds at the initial time. Find the following: 1. Time at which the car attains a speed of 20 meter per seconds. 2. Acceleration of the vehicle after 5 sec 3. Distance traveled by the vehicle when accelerated to a speed of 20 meter per seconds.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The City of Gainesville and FDOT, in an attempt to proactively address the growing need for capacity in the western area of Gainesville, has identified a potential alignment for a new freeway to UF campus. The FDOT district has contracted you to design this new freeway and identify any additional concerns with this potential freeway. Note that this is an open question, and you may need to make the following assumptions during your work: Lane width (e.g., 12 ft. or 11 ft) Shoulder width (e.g., 6 ft.) Interchange density (e.g., 1 interchange/2 miles) Number of lanes (e.g., 3 or 2 lanes each direction) Hourly volume V= * D*AADT (e.g., =10%, directional distribution D=50%) A design structural number (e.g., SN= 5.0) The following traffic characteristics are expected on this freeway: AADT=30,000 veh PHF=0.95 85% passenger cars Two 2-kip single axles 7% RVs One 10-kip single axle One 24-kip tandem axle 5% single-unit trucks One 12-kip single axle Two 32-kip tandem axles 3% tractor-trailer…
(c) The Jabatan Kerja Raya (JKR, 2008) Specification of roadwork requires that air void of asphalt concrete should be in the range of 3 to 5 %. Discuss the consequences to the road performances if the contractor failed to fulfill this standard requirement.
The factors influencing highway design include choose one of the following cross section of highway design speed fund and saftey all of the given choices
Plz, solve this problem by using the table. Transportation Engineering-2
What are the parameters in designing highway facilities and safety? Enumerate 5 safety features that you see on the road and briefly describe each.
What is the K- design value for a roadway designed for 70 mph, and G₁--2.5% and G2=3.9%?
Which test is NOT introduced by Strategic Highway Research Program? O Viscosity at 135 C Rotational Viscosity O Pressure Aging Vessel O Dynamic Shear Rheometer
Question number (1) Highway Engineering civil engineering
Q5. Choose the correct answer 1. Curbs are raised structures used mainly on urban highways to: a. delineate pavement edges b. control drainage e. all the mentioned options c. improve aesthetics 2. Why the 30 HV is suitable to be used in traffic volume studies? a. It gives highest volume of traffic within the year c. It is hardly obtained d. none of them b. It repeats many times in a year d. All the mentioned options 3. If the average space headway of vehicles is 25m, then the volume of a traffic lane at a speed of 60 Km/hr a. 2400 vehicles per day b. 2400 vehicles per hour c. 2000 vehicles per hour d. 1000 vehicles per hour 4. Guard rails are barriers that are located: a. On the outside of a horizontal curve with small radius c. At section of high fills b. On the outside of a horizontal curve with big radius d. On the outside of a horizontal curve with big radius and at sections of high fills e. On the outside of a horizontal curve with small radius and at sections of high fills f.…
Q4: On a proposed highway, the speed limit is 120 km/hr, radius of a horizontal curve on this proposed highway is 250 m and the superelevetion is 8%. Is there any design problem? If so, what the action will you recommend to correct the design?
(a) As an engineer at Jabatan Kerja Raya (JKR) Kuala Lumpur Headquarters, you are given the task to design a flexible road for a highway project at Perak. List FIVE (5) parameters of road thickness design required according to Arahan Teknik Jalan (ATJ) 5/85 Amendment 2013.
On a proposed highway, the speed limit is 120 km/hr, radius of a horizontal curve on this proposed highway is 250 m and the superelevetion is 8%. Is there any design problem? If so, what the action will you recommend to correct the design?