The cantilever steel beam as shown below has the rectangular cross section shown, determine the maximum displacement of the beam use E=200 GPa for the modulus of elasticity 200mm 4 KN/m 6 KN .m 350mm 2m 2m 1m %V9 l1.V:OAand shear stresses for the beam9KNSKN/m10 KN/mBA.C+ Im3m2m3m200mm350mmOption 1The cantilever steel beam as shown belowhas the rectangular cross section shown,determine the maximum displacement ofthe beam use E=200 GPa for the modulusof elasticity200mm4 KN/m6 KN .m350mm2m2m1mOption 1SubmitThis form was created inside of University of Mosul. ReportAbuseGoogle FormsII

The given data is: E=200 GPa I=(bh3)/12 I=(200*3503)/12 I=714.58*106

The cantilever steel beam as shown below has the rectangular cross section shown, determine the maximum displacement of the beam use E=200 GPa for the modulus of elasticity 200mm 4 KN/m 6 KN .m 350mm 2m 2m 1m

The cantilever steel beam as shown below has the rectangular cross section shown, determine the maximum displacement of the beam use E=200 GPa for the modulus of elasticity 200mm 4 KN/m 6 KN .m 350mm 2m 2m 1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A T-beam with drawn x and y axes is shown in figure 2. Determine the moments of inertia of the beam.
In the beam given below, it is subjected to a load of L= 3 m and a uniformly distributed load q=10 kN/m. Calculate the rotational value at point A based on the hand bending stiffness?
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1850 in.4]. For the loading shown, determine:(a) the beam deflection at point A.(b) the beam deflection at point B.Assume MA = 180 kip·ft, P = 25 kips, LAB = 7.3 ft, LBC = 11 ft.
Shown in the figure attached is a beam. Given the loading and support condition and assuming that EI is constant for the beam, determine the (a) The equation of the elastic curve, (b) The deflection at the left end of the beam, and (c) The support reactions By and MB.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m
The BC rod in the carrier system shown in the figure has a circular cross section. diameter 25 mm and Tensile Strength 210 MPa and Modulus of Elasticity 2x105 It is MPa. Since a load of 640 kg is hung on the D end of the system; For BC bar: a) Tensile stress, b) Safety coefficient, c) Calculate the length change amount.
Number 9
I need the answer as soon as possible
!!!
Show complete and neat solution
2. A linear spring of stiffness k N/mm is to be designed to stop a railroad car, with a mass of m kg, traveling at v, km/hr within x mm after impact. Find the smallest value of k, in terms of m, ve, and x, that will produce the desired result. Hint: a dx = v dv. mim Vo k wwwM
Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, s 90MPA, T. S 65MPA and the angle of rotation of the free end limited to 11°. Use GS 84 GPa and Ga = 27 GPa. %3D %3D 75 mm Aluminum Steel 50 mm 2 m 1.5 m