The bracket BCD is hinged at C and attached to a control cable at B. For the loading shown, determine (a) the tension in the cable, (b) the reaction at C. 240 N 240 N a = 0.18 m C -0.4 m- -0.4 m- 0 24

Q: Q-6: Blocks A and B are identical with each weight of W. If the coefficient of static friction…

A:

Q: /Wmsthe value of angle 0f andthevetueof02 -1000N

A: Calculated angles theta 1  and theta 2  .

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: S0ON so

A:

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Finding the y centriod.

A: Given data, the I section is given with dimensionFind outthe centroid along the y-axis

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: where is the T-S diagram

A: Rankine Cycle is a ideal cycle for producing net work output in thermal power plant where water is a…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: Answer in number 7 and 8.

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: Determine Stres

A:

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: what is part number 4

A: Solution:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Find this range. Ds i mm

A:

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: Which of the following statements is FALSE regarding materials experiencing stress within the…

A: Given Stress vs strain plot To write:  WHich statement is false

Q: what is the actual area in part a ?

A: Given: Q=5000 m3/min=5000m3min×1min60 sec=83.33 m3/s V=6.0 cm/s=6.0cms×1m100cm=0.06 m/s

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Q: A) Are all the nodes in the same plane?. B) To the surface, what would the unit of perpendicular…

A: The 3 dimensional geometric coordinates of the system are taken in uniform units as millimetre. They…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.