The bottom plate of a barge's hull (Figure below) is curved with the radius of 1.75 m. When the barge is submerged in sea water (S.G. = 1.03), determine the total hydrostatic pressure force (FR) and direction (angle) on plate AB per unit length of hull. B 1.75 m A = 3 m

The bottom plate of a barge's hull (Figure below) is curved with the radius of 1.75 m. When the barge is submerged in sea water (S.G. = 1.03), determine the total hydrostatic pressure force (FR) and direction (angle) on plate AB per unit length of hull. B 1.75 m A = 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem (5): Two designs for a beam are to support moment is equal to M=150 kN.m and I,=0.36135(10³) mª. Determine the maximum normal stress for be considered. consider the I=0.21645(10*) mª, part A and B. 200 mm. 200 mm. 15 mm 30 mm 300 mm -30 mm 300 mm -15 mm 15 mm 30 mm (a) (b)
In the figure below, determine the force F (newton) to balance the weight of the cylinder. |ylinder W 44 kN A = 0.323 m? F = ? Plunger, a = 0.00323 m? 4.6 m YOil, s = 0.78 YOil, s = 0.78 Assume that the weight
A block(unit weight = 19.5 kN/m^3) 0.51m square and 331mm deep floats on a stratified liquid composed of a 200mm layer of water above a layer of mercury(s.g. = 13.6). If a downward force of 1200 N is applied to the center of mass of this block, what is the new position of the bottom of the block relative to the mercury surface in mm?. Write numerical value only and in 2 decimal places.
asap
The cross section of a quarter circular concrete block JKL as shown in Figure 5 is located at thebottom of a reservoir. The width (perpendicular to the paper) is 3 m. The specific weight of theconcrete block is 24 kN/m3. The coefficient of friction between the base of the block and thefoundation is 0.43. Determine if the concrete block is stable or not against sliding and overturningif the water is:A. At side XB. At side Y, with the same water level as A.
A support column that is pinned at one end and fixed at the other is to be used to support a 12000- pound load (P = 12000 lbf). The support is required to be a hollow tube with a length of 3 feet (1 = 12 in.) and an outer diameter of 1.5 inches (d。 = 1.5 in.). Determine the wall thickness of the tube that will maintain a safety factor of 1.8 (n = 1.8) if the material to be used is aluminum (E = 10.4 Mpsi, S, = 60 ksi). do = Ø 1.5 in.
1. A simply supported beam with rectangular cross-section is loaded as shown in the figure. Draw the shear and bending moment diagrams and determine the maximum normal stress due to bending. |15 kN 6 kN/m E A В D 120 mm 0.8 m 2 m
A small boat weighing 40 LT has a submerged volume of 875 ft3 when traveling at 20knots in seawater. (ρ = 1.99 lb-s2/ft4 ; 1 LT = 2240 lb) a. Calculate the magnitude of the hydrostatic support being experienced by boat.b. What other type of support is the boat experiencing?c. Calculate the magnitude of this other type of support.d. What will happen to the submerged volume of the boat if it slows to 5 knots? Explain your answer.
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.9 × 104 kN·m2 is constant for the beam; w = 6.4 kN/m, LHA = 3.0 m, LAB = 6.0 m.
Gate AB in figure below is a homogenous mass of 180 kg, 1.2 meter wide into the paper, resting on smooth bottom B. For what water depth hin meters will the force at point B be zero? Use specific weight of glycerin to be 12360 N/m³ and water to be 9790 N/m3. Water Glycerin h 2 m A 1 m 60° О а. 3.56 оБ. 1.82 О с. 1.12 O d. 2.52
A simply supported beam of length 7 m has a concentrated couple M of 10 kN-m applied at the right end. Determine the location of the maximum deflection from the applied load. O 2.75 m O 2.96 m O 2.50 m O 2.252 m Calculate the value of the maximum deflection. Use E = 200, 000 N/mm^2 and I = 60x10^6 mm^4. O2.62 mm O 131 mm 10.52 mm 5.26 mm
Gate AB in the figure below is 1 m long and 0,7 m wide. Determine the force (F) on the gate and the position x, the centre of pressure. 3m Oil (sp gr = 0.81) ㅗ 1m. 7m 1m 1