The bolted type connection will be used to assemble the given steel members. Determine the safe load that a single turned bolt can carry. Consider only the effect of crushing stresses. (St-52, H) 10 M20 2L 90.90.11 4t

The bolted type connection will be used to assemble the given steel members. Determine the safe load that a single turned bolt can carry. Consider only the effect of crushing stresses. (St-52, H) 10 M20 2L 90.90.11 4t

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E₁ = 15,000 ksi and a diameter of d₁ = 0.40 in. Aluminum rod (2) has an elastic modulus of E₂ = 10,000 ksi and a diameter of d₂ = 0.70in. Aluminum rod (3) has a diameter of d3 = 1.00in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L₁= 6 ft, L₂= 8 ft, and L3 = 3 ft. (a) Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 1.8 is required. (b) Determine the deflection of point D for the load determined in part (a). (c) The pin used at B has an ultimate shear strength of 57 ksi. If a factor of safety of 2.7 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B. L₁ T A Bronze (1) B Aluminum (3) D Aluminum P b (2) L3 •…
Find factor of safety if the Ultimate Stress of a ductile material is 250.94 MPa. If the material is subjected to a loading condition that generates the working stress of 151.27 MPa
Please help ASAP. Help for parts A-B will upload for the other part. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
A hollow short compression member, of normalized cast steel where Su = 65 ksi, is to support a load of 1,500 kips with a factor of safety of 8.0 based on the ultimate strength. Determine the outside and inside diameters if Do =2Di.
Determine the material index for a lightweight, stiff axially loaded bar.
150- 18 F = 25 KN 25 200 25 + 25 € 100- -25 25 50 4 For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.
please help
Part A The strut is supported by a pin at C and an A-36 stoel guy wire AB. (Eigure 1) If the wire has a diameter of 4.8 mm, determine how much t stretches when the distributed load acts on the strut. Express your answer three to significant figures and include the appropriate unita. ? SAn = Value mm Figure 3AANm 27 m
10000 lb is applied at G, pin C can have 5000 max horizontal load and 6000 vertical load, determine max angle of bed
• Bars (1) have a cross-sectional area of A₁ = 0.65 in.2 and a length, L₁= 7 ft. • Bars (1) are made of cast iron with an elastic modulus of E₁ = 24,000 ksi, a coefficient of thermal expansion, a₁ = 12.3 x 10-6/°F and yield strength of oy = 120 ksi. • Bar (2) has a cross-sectional area of A₂ = 1.45 in.² and a length, L₂ = 5.5 ft. • Bar (2) is made of stainless steel with a coefficient of thermal expansion, a₂ = 10.6 × 10-6/°F. • The stress-strain diagram provided below presents the results of the stainless steel's (i.e., Bar (2)) bar tension test. • There is a gap of A = 0.1 in. in the connection at B and a = 3 ft. • All bars are unstressed before a load P = 12 kips is applied and the temperature increases by AT = 40°F. Stress-strain diagram for stainless steel bar: (1) a Stress (ksi) L2 Rigid bar 120 100 80 60 40 20 0 0 0 B (2) P a (1) C Upper scale L₁ Connection details at node C Lower scale. C 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.006 0.008 0.010 0.012 0.014 0.002 0.004 Strain…
Determine the safe tensile load for bolts of (a) M 17 and (b) M 26. Assume that the bolts are not initially stressed and take the safe tensile stress as 305 MPa