The blow counts for an SPT test at a depth of 6 m in a coarse-grained soil at every 0.152 m are 10, 10 and 10. A donut automatic trip hammer and a standard sampler were used in a borehole 152 mm in diameter. The SPT N value is: O 1.8 O 2.5 O 3.20 O 4. 10

The blow counts for an SPT test at a depth of 6 m in a coarse-grained soil at every 0.152 m are 10, 10 and 10. A donut automatic trip hammer and a standard sampler were used in a borehole 152 mm in diameter. The SPT N value is: O 1.8 O 2.5 O 3.20 O 4. 10

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solve question 2 please
Test 1 amd test 2 are image 1 and image 2
Q.
Please solve with all work shown. Thank you
A 6 in diameter exploratory boring has been drilled through a fine sand to a depth of 19 ft. An SPT N-value of 23 was obtained at this depth using a USA safety hammer with a stan-dard sampler. The boring then continued to greater depths, eventually encountering the groundwater table at a depth of 35 ft. The unit weight of the sand is unknown. ComputeN1,60, f′, and Dr at the test location, and use this data to classify the consistency of thesand.
x 18 The effective shear strength equation (S = T₁ = 25+5 tam 30); expressed for a saturated clayey soil. In undrained test on a sample of the same soil using the shear box apparatus, the following data at failure were recorded :. Shear Stress = 90 kPa a) What and Normal stress = 180 kPa pore water pressure in the specimen at time of was the failure (assume Øu= 0). Find the Unconfined compressive strength (Od max) for the same soil an Unconfined. when tested in Compression test. c) Find the major principal stress when a sample of the same soil is tested in Ul test with confining pressure of (200 kPa).
sand deposit has been identified beneath a site located adjacent to a river. The sand deposit is 15 feet thick and the top of the layer is 12 feet below the ground surface and overlain by a very stiff clay and is underlain by bedrock. The water level has been measured to be at a depth of 10 feet. The standard penetration resistance of the layer has been determined to be 12 blows per foot and a standard sampler was used; a drill rig with a safety hammer with an efficiency of 60% was used. The length of the drill rod is 10 meters and the borehole diameter is 5 inches (127 mm). The design earthquake has been designated as a moment magnitude 6-3/4 event on a nearby fault and the maximum ground acceleration is expected to be 0.40 g. The wet unit weight of the clay soils is 150 pounds per cubic foot and the wet unit weight of the sand soils is 180 pounds per cubic foot. The sands have 35% fines content according to a grain size analysis. Compute the factor of safety against liquefaction of…
A standard penetration test has been conduted at a depth of 15 ft in an 8-inch diameter exploratory boring using a USA-style safety hammer and a standard sampler. This test produced an uncorrected N-value of 12. The soil inside the sampler was a fine-to-medium sand with Dsq = 0.6 mm. The vertical effective stress at this depth is 1100 lb/ft². Adjust the N- value as described in Class handout, then compute the relative density and classify the soil using Table 3.3.
Question A sample of dry sand was tested in direct shear test apparatus under a normal load of 72 kg. The shear load required to fail the sample was found to be 36 kg. The angle of internal friction () will be:
Shear Strentgh of the soil 2014
A sand deposit has been identified beneath a site located adjacent to a river. The sand deposit is 15 feet thick and the top of the layer is 12 feet below the ground surface and overlain by a very stiff clay and is underlain by bedrock. The water level has been measured to be at a depth of 10 feet. The standard penetration resistance of the layer has been determined to be 12 blows per foot and a standard sampler was used; a drill rig with a safety hammer with an efficiency of 60% was used. The length of the drill rod is 10 meters and the borehole diameter is 5 inches (127 mm). The design earthquake has been designated as a moment magnitude 6-3/4 event on a nearby fault and the maximum ground acceleration is expected to be 0.40 g. The wet unit weight of the clay soils is 150 pounds per cubic foot and the wet unit weight of the sand soils is 180 pounds per cubic foot. The sands have 35% fines content according to a grain size analysis. Determine the cyclic resistance ratio, CRR. Use this…