The bent rod is supported at A, B, and C by smooth journal bearings. The rod is subjected to the force F= 840 N. The bearings are in proper alignment and exert only force reactions on the rod. (Figure 1) Figure 1 of 1 > ▼ 2m ▼ C 30 600 B -1m-0.75m Part A Determine the components of reaction at the bearing A using scalar notation. Express your answers using three significant figures separated by commas. 15| ΑΣΦ. 41 | vec d CYC ? Az. A₂ = N Submit Request Answer Part B Determine the components of reaction at the bearing B using scalar notation. Express your answers using three significant figures separated by commas. IVE ΑΣΦ | 4t vec 3 PARO ? B₁, B₂ = N Submit Request Answer Part C Determine the components of reaction at the bearing C using scalar notation. Express your answers using three significant figures separated by commas. IVE ΑΣΦΑ vec SAY ? Cz, Cy= Submit Request Answer 2m N

The bent rod is supported at A, B, and C by smooth journal bearings. The rod is subjected to the force F= 840 N. The bearings are in proper alignment and exert only force reactions on the rod. (Figure 1) Figure 1 of 1 > ▼ 2m ▼ C 30 600 B -1m-0.75m Part A Determine the components of reaction at the bearing A using scalar notation. Express your answers using three significant figures separated by commas. 15| ΑΣΦ. 41 | vec d CYC ? Az. A₂ = N Submit Request Answer Part B Determine the components of reaction at the bearing B using scalar notation. Express your answers using three significant figures separated by commas. IVE ΑΣΦ | 4t vec 3 PARO ? B₁, B₂ = N Submit Request Answer Part C Determine the components of reaction at the bearing C using scalar notation. Express your answers using three significant figures separated by commas. IVE ΑΣΦΑ vec SAY ? Cz, Cy= Submit Request Answer 2m N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please include free body diagrams. Need asap
QUESTION 2) The shaft, first two meters length has a solid cross-section with a diameter of 6 cm and the last one meter length has a hollow cross-section with a inner diameter 5 cm and outer diameter of 6 cm is shown in the figure. If the allowable shear strength tu-35 MPa and shear modulus G=200 GPa, determine the allow magnitude of the torsional moment M for a safe structural system. M M бст IScm B C D lm Im 1m
Solve for Ay and By with FBD. (Please mention no.of reaction forces in supports for better understanding)
9
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.46 in., -0.20 in.). Assume a = 15 ft, b = 30 ft, c = 10 ft, and d = 20 ft. Determine the normal strain in each bar. A Answer: EAB EBC = i i P a (1) B με με X b (2) C d
Use x = 137 y = 37 a = 6 b = 8 c = 1
( Hand written and clean writing )
The torques shown are exerted on pulleys A and B which are attached to solid circular shafts AB and BC. In order to reduce to total mass of the assembly, detemine the smallest diameter of shaft BC for which the largest shearing stress in the assembly is not increased. TA = 300 N m 30 min B TH = 400 N- m 46 nn
4.)show complete solution, final answer should be in two decimal only, i will automatically give upvote.
A bar assembly ABC is loaded with axial force 'P' is constrained at both ends. Analyze a bar element by i) ii) A Determining the reactions at either ends. Determining the reactions at either ends when the joint C is reduced by 'u' mm from wall/constraint joint C. 0.7 L Figure 1 0.5 L U
For the truss shown in the following figure, the temperature of member BC is raised by 110 °C, and member BD is raised by 70 °C. EA=300000 N for all members and a=1/75000 1/°C. Use the stiffness method to do the following: b) Ay = c) B₂ A | C ΤΙΣ Part 1. Calculate the displacements at the joints: a) Az = d) By = e) C₂ mm mm mm mm mm Part 2. Calculate the force in each member: a) NAB = b) NAC = c) NBD = d) NBC = e) Ncp = f) NAD = 5 m N N N N N N B D 5 m