The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R

The bent bar shown is subjected to 3 forces shown. Replace these forces with an equivalent couple M and single force F at point A. Show solution to answers M = 21.8 kN-m, cw Fv = 12.03 kN, D FH = 1.60 kN, R

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solve correctly and show the complete solution.
I need Vc,Mc
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
7.
help! please write the correct answer. no long explanation needed! upvote will be given! Mechanics of Deformable Bodies Which letter is correct answer? A, B, C,.... J?
Use x = 137 y = 37 a = 6 b = 8 c = 1
Q1. A horizontal bar of nagligible weight and assumed rigid is supportad by two rads, AB and CD, and hingad : the right and. Data for the rods are as follows: Rod AB: L= 2 m, A= 1950 mm. E= 80 GPa ; Rod CD: L=2.5 m, A= 1200 mm, E= 200 GPa Ifthe maximum unit stress in AB is not to exceed 90 MPa, and the maximum allowabla load for CDis 110 kN, determine the maximum value of the force F. B F 0.60 m. 1.90 m 1.20 m
2. The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.12 in. Use 2 decimal places. (25 pts) steel L = 4 ft A = 0.5 in? E = 29 × 10° psi P =? A B C 3 ft 2 ft
Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation which contains that force as the only unknown. The forces are positive if in tension, negative if in compression. - 3.5 m Answers: BC= BE= A EF= 3.5 m i i i B 3.5 m 3.5 m C 2.4 m E 26.5 KN 3.5 m KN KN KN D
A 0.500 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.3 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. 3 Answer: Tmax = psi 1/3