The beam shown is subject to a shear force (Q) of 100 kN. Find the maximum shear stress. Maximum shear stress (t) occurs at the neutral axis (NA). 1) Find NA. 2) Find moment of inertia, Ixx. 3) Use T = QAY/b/ to find shear stress (T) 13 260 13 200 147 X 20

Q: is the answer 11532?

A:

Q: 35 aw the projections of this shape 25 20 20 A

A: GIVEN:   TO FIND: Draw the projection of the given shape.

Q: The following is the bearing and length measurements of an opentraverse A) Determine the latitude…

A: The latitude of the traverse line is extend on the north and south direction and departure of the…

Q: When are the singularity functions used?

A: Solution-  We can observe that the shear and bending moment expressions get increasingly complicated…

Q: Determine the X coordinates of the centroid of the trapezoidal area shown.

A: Given data : The given figure in divided into Rectangle and Triangle Rectangle: Width (B)=120 mm…

Q: Give other methods of determining the horizontal distance between two points.

A:

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the 2D Orthographic Projection (Front,…

A: Asked: To draw the orthographic projections of the given object.   The following tools are used to…

Q: Find the centroid of the following cross-sections and planes.

A: Centrodal distanceX = 5.333 inY = 5.667 inExplanation:Step 1:Step 2:

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: Examp;e: The following Figure with two projections, assign the types of these projections and draw…

A: The type of projection is first angle projection. The view shown below are  front view and right…

Q: Which of the following are common software for Design / Constructability Review? AutoCAD or…

A:

Q: Given the Isometric View, draw the following: Top View Front View Right Side View Section View…

A: (Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three…

Q: 1.13 List the legal requirements for registration as a land surveyor in your state. 1.14 Briefly…

A: There are different eligibility criteria to become a land surveyor. One should need to fulfill all…

Q: Find centroid of figure from X axis

A:

Q: Find the centroid of the shaded area in the attached file Y k3cm Зст 1cm Зст 1cm 7cm

A: Schematic figure of the above problem:

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: question being asked here is to draw the above diagram using AUTO CAD program and also clearly…

Q: 12. To make a stretch to an object, the procedure is: left click stretch icon, select the object,…

A:

Q: determine the centroid of the area shown with respect to the given x-axis

A:

Q: Give the vector in cartesian coordinates that extends from B(4, 20degrees, 10degrees) to W(7,…

A: The given data is shown below: B=4,20 degrees, 10 degreesW=7,120 degrees, 75 degrees

Q: 6"

A:

Q: How to create stacked bar chart in tableau

A: This question is related to the Computer-aided design software from Civil Engineering. This is…

Q: Map scale is identified as a ratio between Select one: O a. ground distance to map distance O b. map…

A: Given data : The value of distance on map=DM The value distance on ground=DG   Required : Map scale

Q: Figure 2

A:

Q: the centroid location formulas on step 2 come

A:

Q: earson MyLab and Mastering X roblem 9.19…

A:

Q: B Look to the Contour map above Solid line is the ground surface level Dashed line is Water table…

A: Contour lines are drawn on contour maps which represents the elevation or depression at any…

Q: Determine centroidal coordinates of the volume. 610 mm 813 mm 1220 mm wu 099

A: Consider the figure,

Q: Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method).…

A: Solution:- At first show the starting point of 20.20 then inclined upwards with the base, make an…

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: What are velocity charts?

A: The Velocity Chart displays the value amount delivered in each sprint so as to forecast the work…

Q: 1 / 2 \text { inch } \times 1 / 4

A: To find:- 1/2*1/4

Q: Explain 1st and 3rd angle of projection

A: First angle projection and Third angle projection are two different methods of creating a 2D drawing…

Q: The point Coordinates have unlimited style to appear when inserted in * AutoCAD drawing False True…

A: 1. False. There are 3 types of coordinate display style i.e. static, dynamic and distance and angle.…

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: give me answer for 700 m radius?

A: Design speed (V) = 80 kmph Superelevation provided (e) = 7% or 0.07Radius (R) = 700 m

Q: A single Line command is the easiest and most common to use due to its similarity to Microsoft word.

A: Single line command is used to insert text of single line which can include name or a city. unlike…

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.