The beam shown is reinforced for tension at the bottom with 6-28 mm bars and at the top with 3-22 mm bars. Use f'c = 22.64 MPa and fy = 414.7 MPa, Use the following dimensions: d = 592 mm dc = 75 mm btop = 281 mm bbottom=517 mm t = 137 mm d bbottom Calculate the factored uniform load the beam can support if it spans a simple support of 7.65 m. d' biop

The beam shown is reinforced for tension at the bottom with 6-28 mm bars and at the top with 3-22 mm bars. Use f'c = 22.64 MPa and fy = 414.7 MPa, Use the following dimensions: d = 592 mm dc = 75 mm btop = 281 mm bbottom=517 mm t = 137 mm d bbottom Calculate the factored uniform load the beam can support if it spans a simple support of 7.65 m. d' biop

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer number 2 pls
Please Asap
Kindly double check your answer
Determine the magnitude of the force (lb) in member CD of the truss shown if P = 32592 lb, Q = 32061 lb, and y = 6.8 ft. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate whether the force is tensile or compressive: use T if tensile and C if compressive.
A rectangular beam has b = 300 mm and d = 410 mm. The beam is used to carry a factored moment of 24 kN-m. Assume f'c = 28 MPa and %3D fy = 280 MPa. Calculate the required steel area in mm2. Express your answer in nearest whole number.
Determine the required tension steel area for a rectangular beam with given properties below, d' =75mm b = 350mm d = 470mm fc' = 30MPa fy = 400 MPa A. Mu = 470KN-m, As = mm2 B. Mu = 1000KN-m, As = mm2
For the gusset plate with truss members at joint as shown in the figure, compute T force if the value of F is Kilonewton. 72 8 kN 45 5 kN F
For the following problems use an allowable stress equal to 25 ksi for bothtension and compression. Calculate the volume of the truss.PART A. Use the beam-truss analogy to design the following truss.PART B. Perform the structural analysis of the truss and design each member using itsactual internal force. Compare the truss volume to the one of PART A.
Determine the force in members the EF and GI of the truss shown & indicate whether the member is tension or compression. (Choose all correct answers).
The lower ends of the three bars shown are at the same level before the uniform rigid block weighing 38 kips is attached. Each steel bar has a length of 2 ft, and area of 1.9 in.?, and E = 30 x 106 psi. For the bronze bar, the area is 1.4 in.2 and E = 13 x 106 psi. Determine the length (in feet) of the bronze bar so that the load on each steel bar is twice the load on the bronze bar. Bronze Steel Steel W 2 ft 2 ft
Determine the magnitude of the force (lb) in member BD of the truss shown if P = 35023 lb, Q = 33321 lb, and y = 8 ft. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate whether the force is tensile or compressive: use T if tensile and C if compressive.
a w12x65 column section shown in the figure is pined at each end and has an additional support in the weak direction at a point 4.19m from the top. Use x = 4.71 K=1 A = 12323 rx = 134.11 ry = 76.71 Fy = 248 Determine the a) design compresive strength (KN) b.) Elastic critical buckling stress (MPa) c.) Flexural buckling stress D.) Critical slenderness ratio E.) Nominal compressive stress F.) allowable compressive strength