The beam shown is laterally supported at the ends only. Which of the following most nearly gives the value of L₁.

Q: Define Reliability-based design

A: Reliability-based design- It is defined as a  concept that helps in planning, building, and…

Q: 5.1 The recommended scales for use on technical drawings are specified in the following table.…

A: To find: Choose the suitable code for the given scales for use on technical drawings.

Q: Explain the principle of 5S in Construction. Complete the answer please.

A: Introduction- Construction- It refers to the methods and business associated with assembling and…

Q: show the integration process

A: To show the integration process

Q: What is a pick

A: The term pick may be defined in various ways according to the situation Firstly Pick may defined as…

Q: Which of the following is the largest scale? O 1cm:1mile O 1 mm:10m O. 1:1000 1cm:1km

A: to check largest or smallest scale firstly convert all numerator and denominator in same unit of all…

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: What is binder?

A: A binding agent, or binder, is a medium that is used as a way of supplying structural support to…

Q: Good structural design is more related to correct natural sense than to sets of

A:

Q: Give the table mentioning AQI Values, Descriptors and Colors used?

A: The Air quality Index is often abbreviated as AQI. The government has prescribed some set of values…

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: Give 2 uses of nails

A: Brief concept- Nails- It is a piece of metal that pointed at one end and flattened at another end.

Q: What materials are used as firestopping?

A: Solution: Firestopping is made up of materials that have strong fire resistance and not at all burn…

Q: The Lowest level of design pattern is called a. Design Patterns b. Architectural Design Patterns c.…

A: The lowest level of design pattern is called  d. Analysis pattern

Q: what was the unit used in the plan shown above ? autocad

A: There base unit in AutoCad is inch.

Q: The solution came out all in one line. Making it difficult to understand. Please Can it be written…

A:

Q: Discuss Shape Factors

A: Shape factor:- Shape factor is defined as the ratio of plastic moment and the yield moment of the…

Q: 13.1500 13.1500 4 0000 - -2.0000 4.0000 -3.3500 0.0000 2.0000- 3.8000 -3.3500 2.0000 2.0000 2.0000…

A: We need to find out One Way Slab and Two way slab If Ly/Lx is equal to or more than 2 then One way…

Q: Q: Define civil engineering

A: Civil engineering:

Q: What is bulk density? own word plss type written

A: Bulk density is the ratio of total mass of soil to the total volume of soil mass.

Q: Define Dynamic Replacement.

A: Dynamic Replacement is the dynamic compaction variation, and comprises of delivering energy of…

Q: some examples of the term OFFSET

A:

Q: Explain the Modified Mercalli scale.

A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…

Q: 9- The Scale The scale of a drawing is... Lo = X Lo = Lo= e= If e 1: Full size representation. e 1:…

A:

Q: Plan the structural schematic layouts for various RC structural systems.

A: AutoCAD software is very useful software in the design and analysis of the structure or any…

Q: Write the types of structures in detail.

A: The type of structure to be constructed for a purpose depends upon the use of structure, load on…

Q: Law of contract is important for Civil engineers. Give three examples.

A: In a contract, responsibilities and obligations are outlined and agreed upon by the two parties…

Q: (a) Describe the purpose of detail design in your own words.

A: Detail design: Detail design involves the complte design procedure. The design procedure of every…

Q: What materials are included in Division 9 of the MasterFormat?

A: Some divisions of the Master Format are : Division 6 - Wood and plastics Division 7 - Thermal and…

Q: Create a structure diagram that even individuals without technical knowledge may comprehend. In…

A: Solution: Let's assume the hospital to be a reference model for our structure. We are going to…

Q: What do you mean by fail safe design

A: Fail-safe designs are the methods of designs in which various techniques can be used to mitigate…

Q: What are the CAD tools that one can use in Digital system design?

A: The method of creating and documenting a product using computer software is known as computer-aided…

Q: Functional Analysis - complete two the Blackbox model - list sub-functions at list 5 critical…

A: In functional analysis, a Blackbox model is a representation of a system where the internal workings…

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.