The beam shown carries a uniformly distributed load of 2kN/m along the span of BC. The beam is supported by a roller at B and pin-connected at C. Use conjugate method and moment-area method to solve the following: a. Compute for the slope at B using conjugate beam method b. Compute the displacement of A using conjugate beam method c. Compute the displacement of A using area-moment method

The beam shown carries a uniformly distributed load of 2kN/m along the span of BC. The beam is supported by a roller at B and pin-connected at C. Use conjugate method and moment-area method to solve the following: a. Compute for the slope at B using conjugate beam method b. Compute the displacement of A using conjugate beam method c. Compute the displacement of A using area-moment method

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A) determine the value of constant of integration C1 and C2 in lb-ft^2. B) determine the slope at point B. C) determine the defelction at point B in inches.
Subject: Structural Theory 2 Task: Answer this question in different methods such as Double Integration method, area moment method, conjugate beam method, AND virtual work method.
SOLVE ONLY ONE OF THE FOLLOWING, using either the Unit Load Method/Method of Virtual Work or the Castigliano's Theorem: A A.) For the truss loaded as shown in Fig A, calculate the total deflection at joint D. Consider uniform cross sectional area A= 500mm² and modulus of elasticity E for all members is 200 GPa. B.) For the rigid frame shown in Fig B, calculate the horizontal deflection at point C. Members have the same moment of inertia of 1440 x 104 cm4 and E is constant at 210 GPa. P= 151 kN P in KN B H O G 4@3m 12 m Fig. A P in kN LL D 4m 120 kN/m B 120 kN/m A 4m Fig. B P in kN 3m 5m
The El of the beam is constant. Virtual forces. 8) Using an energy method (strain energy, virtual forces, or Castigliano's Theorem-your choice!), find the displacement at the free end of beam ABC. For the beam, EI is constant. L B b P dc=
Consider the truss shown in (Figure 1). Assume the members are pin connected at their end points. TakeA = 130 mm2, and E= 200 GPa for each member. Use the method of virtual work to solve this problem. Determine the horizontal displacement of joint D measured leftward. 8 kN 3 m 3 m 4 m C B
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
Pls answer fill in the blanks C1, C2 and Ma.
Beam AC with constant EI has a roller support at point B and slider support at point A as shown in the figure below. Using the conjugate beam method to determine the magnitude of the couple moment M0 in terms of P if the displacement at point C is zero. Hint: the slider support can be considered as a fixed support but can move freely in the vertical direction. Use these properties to find the corresponding conjugate support for this problem.
do asap
For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x). Include the beam reactions in this expression. (b) Integrate w(x) twice to determine V(x) and M(x). (c) Use V(x) and M(x) to plot the shear-force and bending-moment diagrams. Let a = 5.0 m, b = 1.7 m, wA = 16 kN/m, and wB = 46 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Determine/derive the Shear and Moment Equations of each segment of the beam (kindly include the FBD). Compute the Reactions and Draw the detailed Shear and Moment Diagram indicating values.