A) determine the value of constant of integration C1 and C2 in lb-ft^2.B) determine the slope at point B.C) determine the defelction at point B in inches. Double IntegrationThe given overhanging beam is loaded as shown. Use E = 1.5 x 10^6 psi and I =40 in^4180 lb/ft1350 lb-ftAE+ 9 ft + 9 ft 9 ft → 9 ft →B.

Answered: Image /qna-images/answer/cdfc186e-1212-49e7-9145-9819e9fea654.jpg

Answered: en overhanging beam is loaded as s 1350…

Engineering

Civil Engineering

en overhanging beam is loaded as s 1350 lb-ft A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

determine the sign and magnitude of (a) the slope at end A, (b) the deflection at end A (use method of superposition) P MA = Pa C A a- B L
Using double integration method, for the overhanging beam shown, (a) derive the equation of the elastic curve, (b) compute the value of ô at the right end and (c) calculate the value of ô midway between the supports. Use E = 29 x 103 ksi and I= 204 int. |6 kip 2 kip/ft |3 kip .B 6 ft- - 6 ft- 6 ft
Determine the following unknowns on the beam shown using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. A. Deflection at point B in mm. B. Deflection at point E in mm. C. Slope of the elastic curve at point D in degrees.
17. The simple beam shown supports the concentrated load P = 2000 N. Dimensions a and b are 1.2 m and 1.5 m, respectively. Determine the value of Ely at midspan in N-m³. Rz а. 784 c. 934 b. 806 d. 986
Determine the displacement at C and the slope at B. E = 200 GPa, | = 70 x 1016 mm^4. Use Conjugate Beam Method. Express your answers in millimeter and degrees respectively. 4 kN 4 kN C B tisatism -15 m15m- -3 m- 3 m
From the figure, the dimension of the beam is 7 in height by 5.5 in width. a. Compute the slope at Ab. Compute the displacement at B
A beam is subjected to equal bending moments of Mz = 3100 N·m. The cross-sectional dimensions are b = 180 mm, c = 35 mm, d = 70 mm, and t = 7 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
Figure 5 shows Beam ABCD. The supports at A and C are pin and roller, respectively. The beam is subjected to a concentric load at the midspan and a uniform load on segment BD. It is noted that E and I are constant. Using the coordinate below. Using the double integration method to determine the slope and deflection at point D. Express the results in terms of EI and show the sign conventions clearly. 20 kN 6 kN/m A В D 3 m 3 m 1.5 m Figure 5
A beam is subjected to equal bending moments of M₂ = 4300 N·m. The cross-sectional dimensions are b = 120 mm, c = 33 mm, d = 67 mm, and t = 4 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. Answer: (a) y= i mm M 1₂ = i mm4 S= mm³ (b) OH = i MPa (c) OK = i MPa (d) gmax= i MPa (typ) b H K
A Review Part C Determine the slope to the right of B. Consider the beam shown in (Eigure 1). El is constant. Assume that El is in kN - m. Suppose that M = 30 kN - m. Use the moment- area theorems to solve this problem. Follow the sign conventicri. Express your answer using three significant figures. V AE It vec 180 Submit Previous Answers Request Answer X Incorrect; Try Again Part D Determine the displacement at D. Figure Express your answer using three significant figures. V AZO r vec 180 1 kN-m X EI An = Submit Prevlous Answers Reguest Answer To X Incorrect; Try Again 3 m 3m
Consider the figure below. a. Determine the location of the neutral axis. b. Determine the Inertia of the section. Hollow 100 R 150mm R*25mm
A beam is subjected to equal bending moments of Mz = 3100 N·m. The cross-sectional dimensions are b = 180 mm, c = 35 mm, d = 70 mm, and t = 7 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. Part 2subparts