The beam AD is loaded as shown. The coefficients of static friction at the wedge's top and bottom surfaces are µca = 0.25 and µcB = 0.35, respectively. Neglect the weight and size of the wedge and the thickness of the beam. Determine the horizontal force P which must be applied to the wedge in order to remove it from under the beam. 4 kN/m 10° -P В 3 m 4 m.

The beam AD is loaded as shown. The coefficients of static friction at the wedge's top and bottom surfaces are µca = 0.25 and µcB = 0.35, respectively. Neglect the weight and size of the wedge and the thickness of the beam. Determine the horizontal force P which must be applied to the wedge in order to remove it from under the beam. 4 kN/m 10° -P В 3 m 4 m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.3. Determine the length b of the triangular load and its position a on the beam such that the equivalent resultant force is zero and the resultant couple moment is 8 kN.m clockwise. 4 m 16 kN/m 2 kN/m
Determine the bending moment at point C of the beam shown. 0.5 kN/m A I 3 m C · 6 m 1.5 kN/m B
1. A 6.4 - m beam has a pin support at the leftmost part of the beam and a roller support located at 4 meters from the pin support. It carries a uniformly distributed load of 40 kN/m throughout its entire length. Using shear and moment diagram, A. Calculate the maximum shear. B. Calculate the maximum moment. C. Determine the most economical and lightest S-shape if the flexural stress is equal to 120 MPa. D. Calculate the actual bending stress of the chosen beam.
Situation 5 - A steel drive shaft is 1.80 m long and its outer and inner diameters are respectively equal to 56 mm and 42 mm. The shaft transmits 180 kW while rotating 1t 1800 rpm. Use G = 77 GPa. 36. What is the applied torque in N-m? А. 1008 В. 849 37. Compute the maximum shearing stress in MPa. А. 40.5 В. 42.8 38. Compute the angle of twist in degrees. A. 1.72 В. 1.94 C. 637 D. 955 C. 27.1 D. 36.1 C. 2.05 D. 1.29
3. The cross section of a weightless quarter circular gate AB of width 0.9 m is shown in Figure 3.The hinge is along AA. Calculate the force R at B to hold the gate in this position.
Q.3. Determine the length b of the triangular load and its position a on the beam such that the equivalent resultant force is zero and the resultant couple moment is 8 kN.m clockwise. 4 m 16 kN/m 2 kN/m
k=2 lb/ft -¨¨¨¨¨ B Two blocks A and B have a weight of 11 lb and 6 lb, respectively. They are resting on the incline for which the coefficients of static friction are μA = 0.16 and μB = 0.23. Determine the angle 0 which will cause motion of one of the blocks. What is the friction force under each of the blocks when this occurs? The spring has a stiffness of k = 2 lb/ft and is originally unstretched. Determine the smallest angle which will cause motion of one of the blocks. Determine is the friction force under the block A at this angle. Determine is the friction force under the block Bat this angle.
For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the magnitude of the maximum slope angle of the beam (in degrees) if d = 1.6 m, E = 11.62 GPa , and I =1694446mm4.
For the beam shown, determine the following: a. Rotation at B in degrees. b. Rotation at E in degrees. c. Deflection at E in meters. Use EI = 200 kN-m² A 1m 60 kN-m B 2m C 5 kN/m ↓↓ 2m D E 1m
Determine the smallest horizontal force P (in N) required to move the wedge. The coefficient of static friction at all contacting surface is 0.3 and the angle theta is 20 degrees. neglect the weight of the wedge. If the horizontal force P is removed, determine the largest angle theta (in degrees) that will cause the wedge to be self-locking regardless of the magnitude force applied to the handle. The coefficient of static friction at all contacting surface is 0.3.
Determine the vertical displacement of end B of the cantilevered 6061-T6 aluminum alloy rectangular beam. Consider both shearing and bending strain energy.
A uniform 50-kgf board rests on rough supports located at A and B in the figure. Thefriction coefficient μs=0.60 on both contact surfaces. If a man weighing 80 kgfpulls on the rope with a force of 40 kgf, determine:a) The angles "min" minimum and "max" maximum for which the system is in equilibrium.b) The minimum coefficient of friction that must exist between the soles of the man's shoes andthe soil for each of the cases in section a.