The bar shown is sujected to two vertical loads F & F of 3000 lbs each and 10 m apart. Both are 3 m from the ends of the bar. Draw the shear and moment diagram for the bar loaded as shown, and determine the maximum shear and moment. Determine the maximum and minimum bending stress based on the given cross-section of bar in the figure.

The bar shown is sujected to two vertical loads F & F of 3000 lbs each and 10 m apart. Both are 3 m from the ends of the bar. Draw the shear and moment diagram for the bar loaded as shown, and determine the maximum shear and moment. Determine the maximum and minimum bending stress based on the given cross-section of bar in the figure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An embedded beam is subjected to the loads shown. Determine the stress produced at points A, B ,C, D in the embedment section. The X axis is 72.9 mm from the top edge. Solve correctly please
For the below wooden beam, under the given loading and dimensions: ŢŢ 50 kN C 4m w = 10 kN/m B 150 mmm Calculate ans sketch the shear stress distribution of the section at the support 360 mmm
3.1 Show your complete solution.
1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by combined moments M and axial compressive loads P at its ends. Taking P = 500 kN, determine, based on the Von Mises criterion of yield failure, the largest allowable value of M. d M M P- P.
For the beam and loading shown, consider the n-n cross section. (a) the absolute value of |M| of the bending moment in the n-n section N.m (b) determine the absolute value of the normal stress in the direction of the X axis at point A of the n-n section |σx| MPa in units, c) determine the absolute value of the maximum shear stress at Point A of the n-n section |tmaks| MPa in units. The inside of the beam is full and the cross-section measures are as shown in the figure. Supports only support vertical forces. Take P1 in the question for 220 N and P2 for 323 N. Point A is at the bottom of the beam.
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. Determine the following: a. maximum value of w without exceeding the permissible flexure stress of 10MPa. b. maximum value of w without exceeding the permissible shear stress of 1.2MPa. c. maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.Please show your clean and complete solution. Thanks
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.
Hi, The maximum stress can't be more than 10MPa so that cannot be the right answer. Also where do the figures for 69.5knm bending moment come from?
8
Please write All answer in mpa
Higdon