The axial assembly consists of a solid 1.01-in-diameter aluminum alloy [E- 8900 ksi, v - 0.33, a = 12.4x 10-6/°F] rod (1) and a solid 1.63-in-diameter bronze [E - 15400 ksi, v- 0.17,a = 7.3 x 10-6/°F] rod (2). Assume L;-15 in., L2-29 in. If the supports at A and Carerigid and the assembly is stress free at 6°F, determine: (a) the normal stresses o1,02 in both rods at 167°F (positive if tensile, negative if compressive). (b) the displacement ug of flange B (positive if to the right, negative to the left). (c) the change in diameter Adı of the aluminum rod. B L1 L2 Answers: (a) o1 26.591 ksi, o2 = i 10.209 ksi (b) ug - i 0.0418 in. (c) Ad, = i in. 0.0003288

The axial assembly consists of a solid 1.01-in-diameter aluminum alloy [E- 8900 ksi, v - 0.33, a = 12.4x 10-6/°F] rod (1) and a solid 1.63-in-diameter bronze [E - 15400 ksi, v- 0.17,a = 7.3 x 10-6/°F] rod (2). Assume L;-15 in., L2-29 in. If the supports at A and Carerigid and the assembly is stress free at 6°F, determine: (a) the normal stresses o1,02 in both rods at 167°F (positive if tensile, negative if compressive). (b) the displacement ug of flange B (positive if to the right, negative to the left). (c) the change in diameter Adı of the aluminum rod. B L1 L2 Answers: (a) o1 26.591 ksi, o2 = i 10.209 ksi (b) ug - i 0.0418 in. (c) Ad, = i in. 0.0003288

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid bar ABCD is supported by a smoth pin at D and by vertical aluminum alloy [E=10,000 ksi] bars attached at joints A and C. Bar (1) was fabricated to its intended length L1=40 in. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2=59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by Δ=0.12 in. After bar (2) has been stretched and connected to the pin at C, a load P=20 kips is applied to the rigid bar at B. Use the following additional properties and dimensions: A1=A2=0.75 in2, a = 36 in, b =54 in, and c = 48 in. Determin: a) The normal stresses in bars (1) and (2). b) The deflection at A of the rigid bar.
A steel [E = 29,200 ksi; a = 6.0 x 106/°F] pipe column (1) with a cross-sectional area of A₁ = 5.40 in.² is connected at flange B to an aluminum alloy [E = 10,200 ksi; a = 12.9 x 10-6/°F] pipe (2) with a cross-sectional area of A₂ = 3.50 in.2. The assembly (shown in the figure) is connected to rigid supports at A and C. It is initially unstressed at a temperature of 80°F. Assume L₁ = 117 in., L₂= 139 in., P = 36 kips. (a) At what temperature will the normal stress in steel pipe (1) be reduced to zero? (b) Determine the normal stresses (positive if tensile, negative if compressive) in steel pipe (1) and aluminum pipe (2) when the temperature reaches -14°F. Answers: (a) T= (b) σ₁ = 0₂ = (1) L₁ i i B P L2 (2) °F ksi ksi
Note: give me complete solution a,b,c,d and e. I don't want single answer. Please solve completely
A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?
Mechanical Engineering Subject name : Strength of Materials
A copper [E = 102 GPa, a = 17.1x10-6/°C] rod (2) is placed within a steel [E = 204 GPa, a = 11.6x10-6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 88 mm, its inside diameter is d₁ = 63 mm, and its cross-sectional area is A₁ = 2965 mm². The diameter of the solid copper rod is d₂ = 45 mm, and its cross-sectional area is A₂ = 1591 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 40°C. Pin Answer: 02= i Steel Tube (1) Pin MPa Copper Rod (2)
A copper [E = 104 GPa, a = 17.1x10-6/°C] rod (2) is placed within a steel [E = 208 GPa, a = 12.2x10-6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 103 mm, its inside diameter is d₁ = 80 mm, and its cross-sectional area is A₁ = 3306 mm². The diameter of the solid copper rod is d₂ = 60 mm, and its cross-sectional area is A2 = 2828 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 44°C. Pin Answer: 02= i Steel Tube (1) Pin MPa Copper Rod (2)
A copper [E = 106 GPa, a = 17.5x10-6/°C] rod (2) is placed within a steel [E = 212 GPa, a = 11.2x10-6/°C] tube (1) of the same length. The two components are connected at each end by pins that pass through both the tube and the rod. The outside diameter of the steel tube is D₁ = 97 mm, its inside diameter is d₁ = 84 mm, and its cross-sectional area is A₁ = 1849 mm². The diameter of the solid copper rod is d₂ = 60 mm, and its cross-sectional area is A₂ = 2828 mm². Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by 40°C. Pin Answer: 02= i Steel Tube (1) Pin MPa Copper Rod (2)
need please asap
A steel [E = 30,300 ksi; a = 6.7 x 106/°F] pipe column (1) with a cross-sectional area of A₁ = 5.70 in.² is connected at flange B to an aluminum alloy [E = 10,100 ksi; a = 12.7 x 10-6/°F] pipe (2) with a cross-sectional area of A₂ = 4.30 in.². The assembly (shown in the figure) is connected to rigid supports at A and C. It is initially unstressed at a temperature of 90°F. Assume L₁ = 126 in., L₂ = 156 in., P = 34 kips. (a) At what temperature will the normal stress in steel pipe (1) be reduced to zero? (b) Determine the normal stresses (positive if tensile, negative if compressive) in steel pipe (1) and aluminum pipe (2) when the temperature reaches -11°F. A Answers: (a) T= (b) σ₁ = 0₂ = L₁ tel i L2 °F ksi ksi
Q-A solid 75-mm-diameter Aluminum [E = 80 GPa and 0.3 Poisson ratio] shaft that is 1.25-m long extends through and is completely bonded to a hollow brass |G = 25 GPa] tube, as shown in Figure. Brass tube (1) has an outside diameter of 10 cm, an inside diameter of 75 mm, and a length of 0.75 m. Both the aluminum shaft and the brass tube are securely attached to the wall support at A. When the two torques shown are applied to the composite shaft, determine: (a) The maximum shear stress magnitude in brass tube (1) and Aluminum shaft segment (2) and (3). (b) The rotation angle of joint B and the rotation angle of end c. (1) 30 KN m 12 kN-m Figure 0.5 m
A steel [E = 30,100 ksi; a = 6.3 x 10-6/°F] pipe column (1) with a cross-sectional area of A₁ = 5.80 in.² is connected at flange B to an aluminum alloy [E = 10,700 ksi; a = 13.1 x 10-6/°F] pipe (2) with a cross-sectional area of A₂ = 3.50 in.². The assembly (shown in the figure) is connected to rigid supports at A and C. It is initially unstressed at a temperature of 92°F. Assume L₁ = 115 in., L₂ = 149 in., P = 22 kips. (a) At what temperature will the normal stress in steel pipe (1) be reduced to zero? (b) Determine the normal stresses (positive if tensile, negative if compressive) in steel pipe (1) and aluminum pipe (2) when the temperature reaches -11°F. A (1) L₁ B P P L2 с