The assembly is subjected to a vertical shear force of 100 N. -The cross-section is symmetric top-bottom and left-right. -All dimensions are in millimeters. -Point D is at the neutral axis. -The moment of inertia about the neutral axis is 2.618 x 10 6 mm^4. Calculate the shear flow at point A, B, C, and D. 75 B. A - 15 85 20 10

The assembly is subjected to a vertical shear force of 100 N. -The cross-section is symmetric top-bottom and left-right. -All dimensions are in millimeters. -Point D is at the neutral axis. -The moment of inertia about the neutral axis is 2.618 x 10 6 mm^4. Calculate the shear flow at point A, B, C, and D. 75 B. A - 15 85 20 10

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

complete solution pls answer in 20 mins
The cantilever beam shown is an aluminum pipe that has an outside diameter of 114 mm and an inside diameter of 97.3 mm. A moment of 3 kN-m is applied at the free end. Find the rotation at the free end of the pipe. Neglect the weight of the pipe. М 33KN.m 2m Mod. of Mod. of Coeff, of Elasticity Rigidity G Thermal Ultimate Strength Density kg /m3 x 10 Tensile Yield Strength F, MPa Expansion a m/m/C x 10-6 Poisson's MPa MPa MPa Ratio Material x 10 x 10 Tens. Comp. Shear Steel ASTM A36 or A501 7.85 207 83 250 400 11.7 0.25 Steel (high-strength low-alloy) ASTM A992 7.85 207 83 345 450 11.7 0.25 Steel AISI 1020 hot-rolled 7.85 207 79.3 210 380 11.7 0.25 Steel AISI 1040 hot-rolled 7.85 207 79.3 290 520 11.7 0.25 Stainless steel 7.85 200 80 280 580 410 11.7 0.25 (annealed) Cast iron (gray) 7.21 103 41 140 550 220 10.6 0.26 Aluminum allov 2.64 70 28 240 260 190 23.6 0.33 6061-T6 Magnesium alloy 1.794 45 17 210 280 140 26.1 0.34 Titanium alloy 4.40 114 45 900 970 690 9.7 Nominal Outside Inside…
Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB Part A If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00470 mm/mm, determine the displacement of point B
F1 (kN) 30 mm 80 mm 30 mm 80 mm F2 (kN) 30° 400 mm The system is loaded with F1 (100) and F2 (200) as shown. Determine the principal stresses, principal planes, and maximum shearing stress and show the stresses on an element (a) at point H, (b) at point K.
A portal frame PQR is subjected to uniformly varying load of maximum intensity 20 kN on an attached arm QT as shown in figure. Find the rotation at the hinge support R (in radian) E = 2.5 x 10 MPa I = 8 x 104 mm² Given: 20 kN/m P 3 m -1.5m- R 3 m
е Q2). A 20m steel tape supported at both ends was used to measure horizontal P distance of CD at a temperature of 35 °C and 60 N tension force measured distance was 350m. Under the standard conditions was found that the tape 19.95m length. Find the actual horizontal distance between CD if: Ts Standard temperature 25 °C Coefficient of thermal expansion of steel tape = 11.6x10-6/°C Po Standard tension = 100N. Modulus of elasticity (E) = 210 kN/mm² Cross-sectional area of the tape = 2 mm² The weight of this tape between supports 8 N
4 - A rubber material is attached between two rigid plates. If the lower plate is held in place, what load P is needed to produce a relative displacement of 0.5 mm between the two plates? The rubber material has a shear modulus G = 0.0010 GPa. 80mm 200mm 400mm
0.2: Consider the cantilever beam subjected to the concentrated load shown below The cross section of the beam is of T-shape. Determine The shearing stress 20 mm from the top surface of the beam of a section adjacent to the supporting wall. 50 KN 120mm 2 т 20mm 120mm 20mm
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.15 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.05 -in. diameter and a solid 1.00 -in. diameter aluminum rod (3). The bar is loaded as shown. Determine the deflection of point D with respect to the fixed support A.
The tube is made of plastic, is 5 mm thick, and has the mean dimensions shown. Determine the average shear stress at points A and B if it is subjected to the torque of 5 N-m.
A hollow titanium [G=31 GPa] shaft has an outside diameter of D = 57 mm and a wall thickness of t = 1.61 mm. The maximum shear stress in the shaft must be limited to 246 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist & in a 690-mm length of the shaft when 80 kW is being transmitted at 11 Hz. Answers: (a) P = i (b) = i kW.
Solution accu