The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Aluminum L= 2 m A = 300 mm? E = 70 GPa Steel A = 250 mm? E = 200 GPa

The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Aluminum L= 2 m A = 300 mm? E = 70 GPa Steel A = 250 mm? E = 200 GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ANSWER FAST
Prellade and Tergpie mem Ponud and N=
Q/2 A/ Fill the Blanks. 1- Metals is more- -than ceramic in this property. 2- The engineering design deals with ---and - 3. Chemical reaction of a material with its environment can be considered failure by 4- prototype is- 5- Ductile fracture is characterized- -and- 6- The ---- is a material that characterize with change their shape when their temperature changes. 7- The product service life is expected to be shorter than anticipated in the design because of -----and - 8- The main characteristic of the ---- have electric properties that are combine between the conducting metallie materials and the insulating nonmetallic materials. 9- The one of the reasons for Development of existing products is---
1-A mold with dimensions of 30 cm x 15 cm x 8 cm is intended in a sand plumbing through an estuary of length 8 cm Find the time required to fill the mold cavity if you know that the area of the entrance section is 3 cm?
32. Fine-grained materials have stress-hardening properties. a. True b. False
Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm? and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing., the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod…
The below column (diameter 1 in.) is subjected to a compressive force where the diameter is increased by 0.0001 in. Determine the shear modulus G of the material. Assume that the material behaves elastically with E= 10000 ksi. P=100Kips L- 12' TOSHIBA
A food product with 80% moisture content in a 10 cm diameter can wants to be frozen. The density of the product is 1000 kg / m³, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -2 ° C. After 14 hours in the freezing medium -30 ° C, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder.
Need correct answer
Aluminum shell 10 in. 1 in. Steel core 2.5 in.
_% od 25m is 9m
• Part A Draw the shear diagram for the baam. Folow the sign convention. Fig.m 1) Clok on "add Vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- You chould not draw an "extra" vertical line at the looation of appled moment. Note 2- Be cure to Indicate the oorreot types of the funotione between the linec, eg. fin your ancwer the type of a funotion Ie "Ilnsar inoressing ciope" for the funotion that actually has linear deoreacing clopa, the ancwer wll be graded as Incorrect Uce the button "ohange cagment" f nsoeccary. 0000 15 kN 10 kN/m 20 kN m 2m 1m No cloments selected v N) 30 20 Im) 20 Add discontinulty ines and seloct segments to add to the canvas Submit dg Aer • Part B Draw the momant diagram for the baam. Follow the sign convention. Cliok on "add vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add funotions between the lines. Note 1- The ourve you chooce from the drop-down…