The assembly consists of two A-36 steel rods and a rigid beam BD (meaning that BD does not deform/deflect compared with the elongation of the rods). Each rod has a diameter of 0.75 inches. If a force of 10 kips is applied to the bar as shown, determine the vertical displacement of the load. 3 ft 2 ft E D -1.25 ft 0.75 ft 1 ft 10 kin

Q: If load P = 20.1 kips, determine the normal force in bar (1). A 6 ft 46.6 kips 39.5 kips 33.5 kips…

A:

Q: What is the vertical displacement at joint F. Assume all members are pin connected at their end…

A:

Q: Axial Deflection Prob 4. The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod…

A: The diameter of each rod is .

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: For aluminum rod,For steel rod,The displacement towards A  to left is,

Q: Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft…

A: To find: The Euler Buckling load. Given: The length of the column, L = 14.63 m. Young's modulus, E =…

Q: Provide final answer and equations used.

A:

Q: e rigid beam is supported by a pin at C and an A-36 steel guy wire AB.

A: Given: The diameter of wire is, d=0.4 in. The distribution load is, w=100 lb/ft. The length of the…

Q: 250 mm D 750 mm 120 N•m The two shafts are made of A-36 steel. Each has a diameter of 25 mm, and…

A:

Q: A cubic block with an edge of 0.2 m and a weight of 98 N lies on another cubic block of the same…

A:

Q: sectional area of Arod = 0.75 in². If a load of P = 24 kip is applied to the end of rod, determine…

A:

Q: A column with rectangular cross section of breadth = 9mm and depth = 4mm, has its both ends are…

A:

Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A If the wire has a…

A:

Q: A metal bar is made out of A-36 steel and has a diameter d = 23mm with the end at A fixed to the…

A: To findCalculate the displacement of point C relative to point A.Givendiameter, d = 23 mmLoad, Load,…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: For aluminum rod,For steel rod,The displacement towards A  to left is,

Q: The bar is made of aluminum alloy 2014-T6. Determine its thickness b if its width is 1.5b. Assume…

A: Given data: The width of the bar, b = 1.5b. The length of bar, L = 5 ft. The applied load, P = 800…

Q: The assembly supports a uniform distributed load = 1.65 kN/m as shown. Part A Determine the…

A:

Q: The aluminum block has a rectangular cross section and is subjected to an axial compressive force of…

A: if you have any doubt comment

Q: diameter brass rod. In order to reduce the weight of the member by 25%, the solid rod is replaced by…

A:

Q: The wing spar ABD of a light plane is made from 2014-T6 aluminum and has a cross- sectional area of…

A: The cross-sectional area is A=800 mm2 The moment of inertia about the neutral axis is I=1.07*10-6 m4…

Q: A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN.…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.