The assembly consisting of a uniform slender bar (mass= 1.5 kg and L=0.49 m) and a rigidly attached uniform disk (mass = 6.8 kg) is freely pinned to point O on the collar that in turn slides on the fixed horizontal guide. The assembly is at rest when the collar is given a sudden acceleration a = 3.4 m/s2 to the left as shown. Determine the initial angular acceleration a of the assembly. The angular acceleration is positive if counterclockwise, negative if clockwise. 6.8 kg 00 1.5 kg 1/7/2 124 LA

The assembly consisting of a uniform slender bar (mass= 1.5 kg and L=0.49 m) and a rigidly attached uniform disk (mass = 6.8 kg) is freely pinned to point O on the collar that in turn slides on the fixed horizontal guide. The assembly is at rest when the collar is given a sudden acceleration a = 3.4 m/s2 to the left as shown. Determine the initial angular acceleration a of the assembly. The angular acceleration is positive if counterclockwise, negative if clockwise. 6.8 kg 00 1.5 kg 1/7/2 124 LA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the crank AB is made to rotate with a constant angular velocity of Q rpm clockwise with no force applied to the face of the piston. (a) determine the velocity of the position P (b) determine the angular velocity and acceleration of the connecting rod BD (c) if the piston mass is m, determine the forces exerted on the connecting rod at B and D (neglect the effect of the weight of the rod)
At the instant shown, the uniform slender rod with mass m = 35 kg is pin-supported at point O. It is subjected to a counterclockwise moment M = 66 N•m, has a counterclockwise angular velocity of W= 5.1 rad/s, and the dimensions a = 0.19 m and b = 0.58 m. Determine angular acceleration of the rod (in rad/s2) at this instant. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Negative sign must be included if the angular acceleration is clockwise. Take g = 9.81 m/s2. O. · M Your Answer: Answer
The 14.6-lb lever OA with 9.6-in. radius of gyration about O is initially at rest in the vertical position (0 = 90°) where the attached spring of stiffness k = 4.3 lb/in. is unstretched. Calculate the constant moment M applied to the lever through its shaft at O which will give the lever an angular velocity w = 5.9 rad/sec as the lever reaches the horizontal position = 0. k= 4.3 lb/in. 13.6"- M G 6 7.6" 13.6"
2. The rectangular block is supported by small rollers at its corners and rests on two horizontal surfaces. If the support h at B is suddenly removed, find the initial acceleration of corner A. (You can use a mass, m, but do you even need to for the answer?) A. B
The 35 lb slender rod AB is 277 in. long and at rest in a horizontal position supported by a spring located at h = 226 in. from the suspension cable at B. If the cable at B fails, answer the following 1) Part A: Determine the magnitude of the acceleration of end A. 2) Part B: Determine the magnitude of the acceleration of end B. 3) Part C: Determine the angular acceleration of the rod.
The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) if the bar comes to momentary rest when theta = 58, determine the spring constant k. (b) for the value k = 65 N/m, find the magnitude of the angular velocity of th ebar when theta = 38 degrees.
The 29-kg spool of outer radius ro=530 mm has a centroidal radius of gyration k=355 mm and a central shaft of radius ri=215 mm. The spool is at rest on the incline when a tension T=204 N is applied to the end of a cable which is wrapped securely around the central shaft as shown. Determine the acceleration aaa of the spool center GGG and the friction force FFF acting at the interface of the spool and incline. The friction coefficients there are μs=0.28 and μk=0.17. The tension T is applied parallel to the incline and the angle θ=16. The acceleration aaa and the force F are both positive if up the incline, negative if down.
The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |AE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation. 164 rev/min 145 mm 305 mm
The system is made up of the 1-m, 6.7-kg uniform rod AB and the two uniform disks (each of 0.10 m radius and 2.2 kg mass). If the system is released from rest when 0- 55", when rod AB has just become horizontal, determine the angular velocity of rod ABin rad/s. Assume the disks roll without slipping. Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. Take g= 9.81 m/s?. 1m
The circular disk of 145-mm radius has a mass of 38 kg with centroidal radius of gyration k bar = 25 mm and has a concentric circular groove of 55-mm radius cut into it. A steady force Tis applied at an angle theta to a cord wrapped around the groove as shown. If T = 40 N, theta = 0, mu_s = 0.11, and mu_k = 0.09, determine the angular acceleration a of the
SHOW COMPLETE STEP by STEP SOLUTION for an UPVOTE The small end rollers of the 8-lb uniform slender bar (length = 4 ft) are constrained to move in the slots, which lie in the vertical plane. At the instant when θ = 30°, the velocity of roller A is 12ft/s down the vertical slot. Determine the angular acceleration of the bar, the acceleration of mass center G, and the reactions of points A and B, under the action of the 6-lb force P. Neglect the friction and the mass of the small rollers.
X Incorrect Each of the bars A and B has a mass of 14 kg and slides in its horizontal guideway with negligible friction. Motion is controlled by the lever of negligible mass connected to the bars as shown. Calculate the acceleration of point Con the lever when the 175-N force is applied as indicated. To verify your result, analyze the kinetics of each member separately and determine ac by kinematic considerations from the calculated accelerations of the two bars. The acceleration is poistive if to the right, negative if to the left. 175 N 255 mm 140 mm C 140 mm Answer: ac = 6.25 m/s2