The body consists of a uniform slender bar and a uniform disk, each of mass m/2. It rests on a smooth surface. Determine the angular acceleration a and the acceleration ag of the mass center of the body when the force P = 5 Nis applied as shown. The value of the mass mof the entire body is 1.15 kg. 345 mm 205 5mm P = 5N m/2

Q: The dot product of two unit vectors: (The answer cannot be found on the other choices.) always has a…

A: When the dot product of any two vectors is equals to 1 then those vectors are in same direction…

Q: . Find the volume of a bronze bushing if it's inside diameter is 1 inch, outside diameter is 1.50…

A:

Q: A tank (contains a fluid of density=1318.4 kg/m3) stands on a frictionless cart (The cart is fixed)…

A:

Q: X 300 mm D 800 mm B

A:

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: For the objects shown below sketch the object in the space provided after rotating it about the axis…

A: Find Rotate the object about the given axis.

Q: Q 4/ Give the names of the components to the parts in the vehicles According to the figures. Cutch 4…

A: Data given-

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: X 300 mm D 800 mm B

A: For constant angular velocity, angular acceleration is zero,

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

A: The mass of casting is 120kg after 6% of its mass was machined off. Determine the mass of the…

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: Describe the Parallel-Axis Theorem for an Area?

A:

Q: Move the forces in the shape to point a

A:

Q: Find the center of gravity of the wire.

A: The centroid, when referring to a solid item, denotes the geometric center or the location where the…

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: handle should be identified as a point of interest. Determine the Degree of freedom.

A:

Q: Please now solve 3

A: this question is based on the concept of material science.

Q: Draw the sectional view of the figure

A: Draw the sectional view of the figure.