The areas in cut of two points of level sections that are 75m apart are 36sqm and 72sqm. Side slope is 3H:2V and base width is 10m. Determine the Volume of excavation using the PRISMOIDAL METHOD and correct the computed volume using the formula for PRISMOIDAL corrections.

Q: Q1: For the shaded area shown in the figure below, determine the centroidal coordinates (xo,yo).…

A:

Q: The three wires are attached to the top of the poles to support the stoplight. Find the tension in…

A:

Q: Locate the centroid Y of the plane area shown in mm from the coordinate axes. r = 72 mm. Write…

A:

Q: express each measurement in meters.Express 2 feet 7 inches as inches.

A: Given: The measurement is 2 ft 7 in.

Q: rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the…

A: Given a rigid beam is being supported by three suspender bars made of bronze and are subjected to…

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

A:

Q: Calculate the Ix and ly of the given figure if location of x-axis is as shown and y-axis is at the…

A:

Q: 3. Five weights of 10, 20, 30, 40, and 50 N rest on a table with the coordinates (0.5, 15*), (2,…

A:

Q: Compute the coordinates of the centroid (x, y) of the area shown. 2013 Michael Swanbom BY NC SA d a…

A: Data given Find: (a) Centroid , X¯ and Y¯

Q: One piece is supported horizontally by 3 cables, as shown in the figure below. In the piece there is…

A: The center of mass of any body with hole can be calculated by determining the volume and centroid of…

Q: Find the centroid of the profile in the figure shown with respect to the origin of coordinates…

A: Given:Required:Location of centroid

Q: The cantilever beam geometry shown is made from steel E=200GPA. Determine the deflection and the…

A: To calculate the value of slope and deflection at point B, using the double integration method. In…

Q: 5. Calculate the centroid of a wire rod bent into the shape of an arc defined by x(y) = 3y² from the…

A: The curve x = 3y2 Boundary condition (0,0) and (12,4)

Q: Present a problem with solution solving the centroid of a miscellaneous solid.

A:

Q: what about K ? how did you calculate 39 ? when I do my calculations I find 35

A: K - Rate of vertical curvature. The value of K is not a calculated one which varies depending on the…

Q: For the objects shown on the left below, circle the letters corresponding to all possible…

A: To select the correct answers among the given options as per the given condition in the question.

Q: Compute the coordinates of the centroid (x, y) of the area shown. a b | | a с d y Variable Value 45…

A:

Q: Q1: - Determine the centroidal coordinate of the shaded area shown in the figure below. Assume all…

A: ##CENTROIDAL Coordinates of Shaded Area ####

Q: SHOW YOUR SOLUTIONS AND BOX YOUR FINAL ANSWER/S. USE BLACK BALL PEN FOR YOUR SOLUTIONS AND ANSWERS,…

A:

Q: magine a house. Describe one-dimensional, two-dimensional, and three-dimensional parts or aspects of…

A: Let's break down the one-dimensional, two-dimensional, and three-dimensional aspects of a house and…

Q: The cantilever beam geometry shown is made from steel E=200GP.. Determine the deflection and the…

A: Due to loading on the beam acting at any point or entire beam makes the beam deflect and that…

Q: Problem 3.10 12 in. 15 in. 4 #10 bars $3 in. f, = 60,000 psi f = 4,000 psi 18 in.-

A:

Q: v2 y1 x2

A:

Q: Determine the centroid of the plane area shown. The indicated distances are radii of…

A: Given data:-

Q: From the figure below, locate the centroid from x and y axes as shown. y2 y1 x1 x2 y1 y2 y3 4 5 5 3…

A:

Q: Please solve the following problem so I can understand with step by step solutions

A: To find the centroid of the given figure, follow the steps below: Step 1: In a 2-D coordinate…

Q: e centroid (7, g) of the area shown. passes through the centroid.

A: Given:- a = 32 mm b = 13 mm c = 16 mm d = 57 mm

Q: roid (7, g) of the area showr

A: Note : we can solve first three part for you according to bartleby guidelines  Given:- a = 27 cm b…

Q: What is the area of the below figure if you know x=24.4? (use trapezoidal rule) Ar 29 27 25 27 25 22…

A:

Q: A box is suspended and being supported by three cables as shown in the figure below. Find the angle…

A:

Q: Draw the following figure on an outer piece of paper and measure with a ruler approximately the…

A:

Q: 2. Find the location of x measured from the y axis. 4" 5" X

A:

Q: Part H - There are 2 questions in this part Refer to your email from Tim which defined values of the…

A: From the given question it is required to calculate the moment of inertia about centroidal axis.

Q: Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you!…

A: Given data: P1=50 kN P2=86 kN  Cross-sectional area of each bar= 406 mm2 It is required to determine…

Q: Situation 2: Determine the x and y coordinates and the resultant of the block with the forces acting…

A: GIVEN: TO FIND:  x and y coordinates and the resultant of the block with the forces acting upon it.

Q: Using the Z section below as a reference, determine the following: Yo 1.5 1.5 Хо 8.0 t.5 Compute the…

A: The given section is a composite section. Divide the section into set of rectangles to use the…

Alloys

An alloy is an admixture of two or more metals or a metal and a non-metal. Since ancient times, man has been using alloys. Alloying helps to retain the properties of the parent matter, such as hardness, strength, toughness, ductility and is corrosion-resistant. Copper alloys such as brass have antimicrobial properties that help to fight against (Coronavirus disease 2019) COVID-19 and other hospital-acquired infections. Some common alloys are brass, bronze, solder steel, etc. Most alloys have a lower melting point than their constituents. This is due to the presence of a nonmetal as one of the constituents that behaves as an impurity and restricts the raise of melting point.