The allowable voltage drop in the figure is 5%. The underground cable is a 3-core copper conductor with PVC insulation. Find the voltage drop of line 6. Mains voltage:220/380 V %E$5 power factor everywhere: 0,8 you can use the underground cable with following Cross section :(convenient cable in suitable place) 6,25,50,95 (mm^2)

The allowable voltage drop in the figure is 5%. The underground cable is a 3-core copper conductor with PVC insulation. Find the voltage drop of line 6. Mains voltage:220/380 V %E$5 power factor everywhere: 0,8 you can use the underground cable with following Cross section :(convenient cable in suitable place) 6,25,50,95 (mm^2)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3 Explain Hydro Power Plant, it importance and its components in details.insert images where necessary.
Answer the following questions. If we would like to connect 5 stations using full mesh topology, what is the number of dedicated links that are required to set up the network? If we would like to connect 5 stations using a star topology, what is the number of dedicated links that are required to set up the network? If we would like to connect 5 stations using a ring topology, what is the number of dedicated links that are required to set up the network? If we would like to connect 5 stations using a ring topology, what is the number of I/O ports per device that are required to set up the network? If we would like to connect 5 stations using a star topology, what is the number of 1/O ports per device that are required to set up the network? If we would like to connect 5 stations using full mesh topology, what is the number of I/O ports per device that are required to set up the network?
None
Please answer the following two questions, thank you.
Whale and Kanmuro are two islands located at the Chimera archipelago. These two are separated by a distance of 24 miles. A power link is to be established between them. The power link delivers a maximum power of 601 megawatts at full capacity with an operating voltage of 527 kilovolts. Note that 1 mile is 1.5 kilometers. Solve for the current at full power capacity in kiloamperes. Express your final answers to four decimal places
Q2: Find the T.F for the system below Force Fin M2
The total solar energy resources in Oman are sufficient to cover the energy demands in Oman can cover the energy demands in Oman if combined with wind energy can cover the energy demands in Oman if combined with wind energy and fossil fuels. none of the given answers is true.
21 V1 R2 Va k V3 2A 4V Vo analysis to determine the voltage at the node V2 in Volts. For the above circuit, with R1-6 Ohms and R2" 2 Ohms, use no Round your answer to the nearest single digit decimal place. For example, if you calculate 3.27 Volts, then enter 3.3 as your answer. A Moving to another question will save this response. P Type here to search
Find ix (current at 1ohm) in the circuit
An electrician charges $425.00 for a wiring job. The cost of materials amounts to 62% of the total cost. Find the amount'of money that the electrician receives for labor
2. Explain the construction of squirrel cage I.M.
Task I: You have been asked by your manager to provide a well written document that explain the concept of SI units. To achieve this the following is required: A) Explain the definition of the following: 1. The unit of a quantity. 2. SI. 3. The basic unit of SI. B) Explain the benefit of the SI. C) Distinguish between basic units and derived units. D) Give three examples of basic units and three examples of derived units (Write their special names and symbols and write the derived units in terms of basic units) E) Explain the benefit of the prefixes. E) For each quantity in Table 1 write the quantity as a metric prefix in engineering notation and fill the corresponding SI prefix name. Table 1 Express each quantity as a metric prefix in engineering notation Quantity Prefix Name 4.4*10^-2 W 57g 3.4*107 2 47511 L