Y D1 D2 B A Refer to the above diagram. D1 and D2 are electrical devices in an electrical power network. The lines connected to devices D1 and D2 are metallic electrical conductors. It is stated that 100 A of "conventional current" flows in the conductor between the locations marked "X" and "Y". In terms of the fundamental concept of charge, explain what is meant by that statement. You should limit your answer to less than 100 words. A quantitative explanation is expected.

Y D1 D2 B A Refer to the above diagram. D1 and D2 are electrical devices in an electrical power network. The lines connected to devices D1 and D2 are metallic electrical conductors. It is stated that 100 A of "conventional current" flows in the conductor between the locations marked "X" and "Y". In terms of the fundamental concept of charge, explain what is meant by that statement. You should limit your answer to less than 100 words. A quantitative explanation is expected.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How you should be thinking about electric circuits? Explain the flow and give an example different from the slides provided.• Voltage • Resistance• Current
In the figure the ideal batteries have emfs ɛ1 = 20.4 V, ɛ2 = 9.05 V, and ɛ3 = 5.40 V, and the resistances are each 2.40 Q. What are the (a) size and (b) direction (left or right) of current i,? (c) Does battery 1 supply or absorb energy, and (d) what is its power? (e) Does battery 2 supply or absorb energy, and (f) what is its power? (g) Does battery 3 supply or absorb energy, and (h) what is its power? (a) Number i Units (b) (c) (d) Number i Units (e) (f) Number i Units (g) (h) Number i Units
Question 3: A very simple model for the distribution of clectricity to a typical home is shown in the figure below. Some of components labeled a, b, c, d, c, f, g and h represent the electrical source to the home, some represent the wires that carry the electrical current from the source to the devices in the home requiring electrical power, some represent lamps, televisions, hair dryers and other devices that require power. Assume you are an engineer in charge of a project and one of your subordinate engineers reports that the interconnection in the figure does not pass the power check. The data for the interconnection are given in the table below. Is the subordinate correer? Explain your answer. If the subordinate is correct, find the error in the data. Explain your answer clearly. Based on your answer identify that which label(s) used for the electrical source, wires or other devices. a e h
23 - Which of the following is true for conductive material?I. Electric current occurs when electrons flow from one end to the other in the conductive material.II. Electric current occurs when free electrons interact with each other and transfer energy to each other.III. Conductive materials can become electrified by friction.IV. Conductors have high resistance. A) I, III and IV B) Only IV C) II, III and IV D) I and III E) II and III
In order to identify the function of the parts of an electronic system, the Blank 1 diagram system representation is used. Blank 1 Add your answer A Si diode has a leakage current Is = 40 nA at room temperature (25°). The leakage current if the temperature increases to 43 °C is nA. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places. Add your answer Short answer. In testing a diode, if the red probe of an analog ohmmeter is tapped at the anode while the black probe is at the cathode, what is the ohmmeter reading if the diode is in good condition? Use the editor to format your answer
A piece of wire has a resistance of R. Another piece of wire has twice the length and also twice the diameter of the first piece of wire. Find the resistance of the second piece of wire in terms of R.
1. A copper wire of unknown length has a diameter of 0.25 inch and a resistance of 0.28 ohm. By successive passes through drawing dies, the diameter of the wire is reduced to 0.05 inch. Assuming that the resistivity of copper wire remains unchanged in the drawing process, determine the resistance of the reduced – size wire. c. 175 ohms d. 225 ohms a. 125 ohms b. 350 ohms
Basic Electrical Engineering Chapter 8. Battery and Cells LESSON TITLECells and Battery
3.Question (a) Look up the definition of unit for clothing insulation, called “clo” value. Convert 1.5 clo to a value with an unit in international standard. (b) In the winter, people wear more cloth to keep themselves warm. You have the option of wearing 2 jackets that are 0.3 cm thick or 1 jacket that is 0.6 cm. Assume they are made of the same material and neglect any effect from cloth openings. Which option should you choose to keep you warm? Draw a thermal circuit to help with your discussion.
QUESTION -8 The plot describing the thermal characteristics of copper wire is given in the figure. Using this plot, for a 1000ft length copper wire with 10 Ω resistance at room temperature (20oC)a) Calculate the resistance value at 100oC.b) Calculate the power consumed in the cable carrying 10A current at this temperature (100oC) in units Watt.c) Calculate the amount of energy consumed in the cable during a day with the conditions in (a) and (b) in units Joules.d) A motor with 600Watt output power that works with 85% efficiency is driven with 10A current carried in the cable at 100oC. Calculate the amount of power transformed (dissipated) into heat in this system.e) Consider that a cooling system is used to cool the cable to 50oC and the cable carries 10A current. How many watts should be the maximum amount of power consumed by the cooling system in order to gain power (consume less total power).
A wire with 3 micron radius is made from 9 cm copper, 0.5 cm iron, and 11 cm copper all joined end to end (i.e., in series). Assume the joints are perfect and have no additional resistance. What is the total resistance of the wire?
What does a compatible charge mean? If a charge doesn't compatible what happens? (I'm not sure about "compatible" word the original question's language is different and contain "harmony" word.)