The allowable shear stress is 10 ksi in the shaft shown. Determine the minimum required outside diameter if section is hollow circle with inside diameter of 1 inch Draw the torque diagram in your solution sheet. Answer in inches and 2 decimal places The allowable shear stress is 10ksi in the shaft shown. Determine the minimum required outside diameter if section is hollow circle with inside diameter of linch. Draw the torque diagram in your solution sheet. Answer in inches and 2 decimal places 8,000 lb-in. 19.000 lb-in. 4,000 lb-in. 7,000 lb-in B

Q: : the components of the 100 lb force are B. l00 A 60 30

A: Given data: Magnitude of the force = 100 lb Need to determine the components of the force along A…

Q: F2 = 40 N %3D 4 m F= 70 N %3D 2 m 3 m B. 3m 2 m 3 m

A:

Q: 8. The linear impulse (1) of the force F- (30) N for t-4 seconds is: a. 40 N.m b. 20 N.m c. 16 N.m…

A: Given data: The time is, t=4 s. Write the given expression. F=3t

Q: Determine the components of the force of reaction at point A. Assume that the positive x and y axes…

A: Given Data:   To Find: (a) Components of forces at A. (b) Moment of reaction at A.

Q: Determine the (f_y) when distance of y = 6.7 mm and the scale of force 30.55 lb/mm

A: Given:distance, y=6.7 mmScale of force, S=30.55 lb/mm

Q: The cable is attached to the boom at A and to point B as shown in (Figure 1) so that x = 60 ft, y =…

A:

Q: I want the methode of counting this two drawing L, and J1 and J2 veryy urgent

A: Full joints are the revolute joint and half joints are the sliding pair.

Q: The x component of the cross product of the vector from C to D times the force F. (Use the format…

A: Solution:-Given dataA≡0,2,0B≡4,4,4C≡0,0,4D≡4,0,0F=105 N

Q: Q5) If the magnitude of the resultant force acting on the bracket is to be 90 N .directed along the…

A:

Q: Solve for A and B. P=400 lbs. 0=30° P 45° B www Drawing not to scale. Use given angles. Magnitude of…

A:

Q: Phi = 40 degrees Theta = 35 degrees F1 = 425 Newtons Alpha = 60 degrees Beta = 45 degrees F2 = 625…

A: Given,  ϕ=40°θ=35°F1=425Nα=60°β=45°F2=625N

Q: QS. Find I, for the shaded area. R25

A:

Q: The shaft Sexerts three force components on the die D. What is the value of 0y in degrees for F2?

A: From the figure: F→1=400 i^ -------- (1)F→2=300×cos 60 i^+A j^ +300×cos 60 k^F→2=150 i^+A j^ +150 k^…

Q: 4015 50 Ib 20 Ib GO 16 2' 4. s'

A:

Q: 4. Use F₁ =3, 6₁ = 2, k₁₂₁ = 4₁ K3 = 2,63 = 1, J₁ = 2₁ J₂=5, find the impulse and step response of…

A: Given: To find: Impulse and step response

Q: The modulus of rigidity is defined as the ratio of shear strain to shear stress. Select one: a.…

A: Option a is correct. The given statement is false.

Q: image below, the force acting he box is F = (C · s²) Determine the work done by force F to the box…

A: Given       Force, F = C. S2  Distance, s = 1.7 Constant, C = 6 Find    Work done, W

Q: Q1/ Two Forces Shown in Fig. (1) acts on the bracket, determine the effect of these two forces…

A: F1 = 200 N F2 = 150 N The angle in-between the two forces are not clear in the picture. Hence…

Q: Q2: Determine (Y). D2 Y Q /sec L (m) D1 D2 220 0.5 5 0.25 D2 Y D1 Hg-

A:

Q: Re = 63 * lo4 if the = 0.25 Re = 63 * De termine ? 169

A:

Q: H G 0° 60 6 kN 6 kN 8 kN Sm Sm Sm Sm

A:

Q: QI) Determine the magnitude and direction of F, so that If the resultant of the three forces act on…

A: Solution: The position of the resultant R is shown in the above figure, Angle made by the force F1…

Q: Q1. The force acting on the gear tooth is F = 20 N. Resolve this force into two components acting…

A:

Q: The x component of the force F acting on point A is? (include units with answer) A. The y component…

A: From above diag coordinates areA15,0,0   B0,9,4  C0,-10,12Force F=75lb

Q: Q 114 Calculate the angle between the two vectors that makes the relationship AB = A correct?

A: Given question: Calculate the angle between the two vectors that makes the relationship A·B = A.

Q: 2-39. Determine the magnitude of F and its direction e so that the resultant force is directed…

A: Consider below FBD based on question:

Q: Determine other F = 0.02 N A = 2m²

A: Given data : Force=F Area=A   To find : Stress

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.