image below, the force acting he box is F = (C · s²) Determine the work done by force F to the box when the box has displaced s = 1.7 m. Please pay attention: the numbers may change since they are randomized. Negative sign must be included if the work done is negative. Your answer must include 2 places after the decimal point, and proper SI unit. N, where constant C = 6 and s is displacement in m.

image below, the force acting he box is F = (C · s²) Determine the work done by force F to the box when the box has displaced s = 1.7 m. Please pay attention: the numbers may change since they are randomized. Negative sign must be included if the work done is negative. Your answer must include 2 places after the decimal point, and proper SI unit. N, where constant C = 6 and s is displacement in m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please show written work
I only need the answer to part c and part d Newton's second law of motion was used to obtain the differential equation mi = -kx - câ that models harmonic motion. a) The dots denote differentiation with respect to time t. Explain the meaning of each term (there are three) and each factor (there are six) in the equation. If MKS (meters, kilograms, seconds) units are used, what are the units of each of the six factors? b) Suppose m =and k = 4 (MKS units). What values of c correspond to a system that is i) i) ii) underdamped, overdamped, and critically damped? c) Solve the critically damped case of the IVP = -4x - ck, x(0) = 1,¿(0) = -10. d) Find the value of t at which x(t) = 0
B7
3 kg 2 kg 7m A 4m4 15m 1m 5 m Find the magnitude of force (F) 4m 1.4 m F = ? 15 N 10 N 50 N Find the length (x) -3m- Pivot Find the magnitude of force (F₂) 15 N xm 8m. 2N 3N
Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE: distances are in non-dimensional units. Can use inches or cm) P1) L1=d=4, theta1=0 degrees, L2=a=1.6, theta2=60 degrees, L3=b=5.5, L4=c=4.5 P1) L1=d=2.5, theta1=0 degrees, L2=a=2, theta2=45 degrees, L3=b=1.5, L4=c=1.5 Please also draw the four-bars to estimate the unknown angles theta3 and theta4.
al Outlook (B BC Canvas EC Canvas CTCLink C Chegg Bartleby PHYS121 TXBK Three forces are applied to a hook. F1 F2 dings 12 13 F3 rt Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F1 15 lb F2 35 lb F3 135 lb a. Write each vector in Cartensian Vector Notation. Round your final answers to 3 significant digits/figures. j lb F = i lb Submit Question
The dependence of thermal conductivity of a material on temperature is given by an empirical equation k = a ebT where a and b are constants, and k is in W/m-K and T is in K. Spot the true statement from the following set. a, a and b have the same dimension as k. b. a has the dimension of k and b is dimensionless. c. a and b are dimensionless. d. a has the dimension of k and b has the dimension of T.
P-3 KN R-2 AN to Figure P1.55 1.55 The force R is the resultant of Pand Q. Determine Q and the angle 0.
B2. Determine the resistance of an aluminium coil of 1.25 cm as diameter consists of 14800 turns and the mean length per turn is 33 cm. Take the electrical resistivity aluminium coil as 0.0175 µN-m. (2 Marks) The area in cm? is The total length in m is The resistance of the coil in 2 is
The floor area of the model in the image below is 500 square inches, and the floor area of the house is 1,280 square feet. If the model has a room with a side length of 5 inches, then what is the scale factor for the model to the actual floor? ©2018 AlessandoMassiniano / Getty mages Plus O 5 in:8 ft O 5 in:12 ft O 5 in:36 ft O 5 in:64 ft
2.107 - This question asks to be solved using the ‘Dot Product’
Please write the final answer with unit 3.Length and diameter of a bearing are equal (d=L). This bearing should be able to withstand the allowable support force of 80 N. Allowable support tension is 20 N/cm?. Determine the length of bearing.