The Airy stress function for a cantilever beam loaded by a force applied at the opposite side to the built-in end is given by p=Axy 3 where the x coordinate runs along the length of the beam, the y coordinate runs along the width of the beam and A is an arbitrary constant which can be determined through application of boundary conditions. Which equation gives the shear stresses, ? 0 О 6Аху O-3Ay² O-6Axy

The Airy stress function for a cantilever beam loaded by a force applied at the opposite side to the built-in end is given by p=Axy 3 where the x coordinate runs along the length of the beam, the y coordinate runs along the width of the beam and A is an arbitrary constant which can be determined through application of boundary conditions. Which equation gives the shear stresses, ? 0 О 6Аху O-3Ay² O-6Axy

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.9.9P: A U-shaped cross section of constant thickness is shown in the figure. Derive the following formula...

See similar textbooks

Similar questions

A U-shaped cross section of constant thickness is shown in the figure. Derive the following formula for the distance e from the center of the semicircle to the shear center. Also, plot a graph showing how the distance e (expressed as the non dimensional ratio e/r varies as a function of the ratio b/r. (Let b/r range from 0 to 2.)
Determine the shape factor f for a cross section in the shape of a double trapezoid having the dimensions shown in the figure. Also, check your result for the special cases of a rhombus (b1= 0) and a rectangle (b1= b2).
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A flexible connection consisting of rubber pads (thickness f = 9 mm) bonded to steel plates is shown in the figure. The pads are 160 mm long and SO mm wide. (a) Find the average shear strain yaiTi in the rubber if the force P = 16 kN and the shear modulus for the rubber is G = 1250 kPa. (b) Find the relative horizontal displacement 3 between the interior plate and the outer plates.
Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
show all steps/solution
Q1) The stress function (x) for the cantilever beam as shown in the figure is given by: P $(x) = (x²-3xy) — 8c a) Is (x) a valid airy stress function? Determine the stress field on AC. b) Verify that this stress field meets the boundary conditions where V = ² c) Verify that the vertical displacement of C is given by 8 = where E is the PL³ 6E12¹ elastic modulus of the material, and I is the moment of inertia of the rectangular section of the plate. с L FIG. 1 x +
For the loaded beam shown below, find the reactions at A and B then draw the shear force and bending moment diagrams then find the location and value of maximum tensile stress. The cross-section dimensions can be shown at section K-K
Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions at the wall of the cantilever are provided. L1= 14.00 ft L2 = 7.75 ft Vc = 87.00 kips Mc = 621.875 kip-ft 20 kips 70 kips 12 kips/ft 6 kips/ft Mc A В L1 L2 99.00 kips O 110.00 kips O 75.00 kips O 64.00 kips O 87.00 kips
1
use kN as final answer