The air is measured at 48 deg. C and 511mm Hg. The duct diameter is 553 mm while the discharge diameter is 315mm The fan draws 4 m^3/s air and the static pressure measured is 3 cm water Determine the total head in terms of water.

Q: Fluid of specific gravity 0.80 flows in a 230 mm diameter pipe. Find the critical velocity in m/s.…

A: Given information, S=0.8, D=0.23m Viscosity Find, Critical velocity

Q: Find the specific speed of the pump, if the discharge through the pump is 160 liters/sec, speed is…

A: Given values are, discharge Q= 160litres/sec=160×10-3m3s speed N=1000rpm ,head H=27.5 m The specific…

Q: A pump has a brake horsepower of 35 hp with an efficiency of 68%. Neglecting frictional losses,…

A: Given:Brake horsepower, BP=35 hpEfficiency of the pump, η=68%Height of discharge, h=60 m

Q: The air is measured at 30 deg. C and 518mm Hg. The duct diameter is 585 mm while the discharge…

A:

Q: nd the diameter of the pipe in mm. The discharge of the pipe is  20 lit/sec with the velocity of…

A: Given data: Discharge of the pipe (Q) = 20 lit/s Velocity of the water (v) = 4.75 m/s Need to…

Q: A fluid (s=0.95) flows through a 85 mm diameter pipe at a velocity of 3 m/sec. Compute the mass flow…

A: Mass flow rate of a fluid is equals to the product of mass, velocity and density of the fluid.

Q: 4 ft 2 ft Determine the rate of discharge and gage pressure at point A. А.

A: Given : The diameter of pipe is The free body diagram is,

Q: :A horizontal pipe, IP4 in diometer, toperv graduolly to 8 in. in dia meter. If the flow I 500 cu f4…

A: Option A is correct.

Q: Water flows through the pipe system as shown, mass flowrate A divides equally into B and C, and…

A:

Q: Find the wark done Farce = 2 N Displacement = 0.045m

A: Given data : Force=F Displacement=d   Required : Work done

Q: A Fluid flows at a velocity of 225 cm/s in a pipe with flow rate of 89.3 Litres/sec. then find…

A: Given data Velocity (v) = 225 cm/s = 2.25 m/s Flow rate (Q) = 89.3 lit/sec = 89.3 x 10-3 m3/s

Q: A horizontal Orifice meter is used to measure the flow rate of water through the piping system of 20…

A:

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

A:

Q: Problem 4 A partly full water tank admits water at 85 N/s weight flow while ejecting water on the…

A:

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

A:

Q: The flow is said to be steady when the: For the Velocity at any point of observation does not change…

A: Introduction A fluid's flow is steady when its velocity, pressure, and all parameters of its…

Q: Looking for the calculations / unit analysis for ... 1.) Inlet Potential Energy 2.) Outlet…

A: Given that, Rate of water, Q=60 GPM,Diameter of water, D=2 in,Elevation of pipe, h=100 ft,Pressure…

Q: Water flows vertically inside the pipe, a manometer with a specific gravity of S=0.6 used to measure…

A: Given      Specific gravity = 0.6 Therefore                   Density = 600 kg / m3

Q: The throat diameter of a perfect venturi meter is 1.93 inches and is placed horizontally in a pipe…

A:

Q: Find the head lost due to friction in a pipe of diameter 5 m and length 5000 cm, through which a…

A:

Q: 1. A combination Pitot tube is being used to measure maximum velocity for water flow in a pipe. The…

A: Here we will use the general formula for velocity in pitot tube.

Q: nction if pipe Veločity 2 discharge and pipe diameter 60 mm. Find the discharge in I/hr and velocity…

A: Concept Of Fluid Mechanics Used

Q: A circular pipe 54 meters long tapers from 3 m to 2 m in diameter. What is the velocity per meter…

A: Given   Diameter at bigger section, d1 = 3 m                                                d2 = 2 m…

Q: ! A B C D =150 mm 4-50 mm 1,5 m 3,6 m 2,4 m

A: given; vertical distance from point C to B (h1)=1.5mvertical distance from point C to D…

Q: Estimate the velocity needed to achieve the intermittent flow of water on a pipe where flow length…

A: Given   Height, h = 74.67 centimeters                  = 0.7467 m

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: Given: Velocity of smaller end (V1)=4.3m/sVelocity of larger end (V2)=2.1m/sLength of the conical…

Q: Fill in the blank which is given below The linear displacement can be also calculated with using the…

A: We know that

Q: Convert the units that are blank with the given data 2. Use equations to obtain results from the…

A:

Q: Q1/. A fan draws in air freely and discharges through a test duct of cros section 0.07 m² in which…

A: Area= 0.07m2Static pressure 20% of velocity pressuretotal efficiency=65%Power=1kW To-Find:- Quantity…

Q: 1. Two round pipes have water flowing through them. Pipe B is half of the diameter of pipe A. If the…

A:

Q: A 20 hp pump with a suction from an open reservoir (10 m above the pump) has a flow rate of 125…

A:

Q: Jaymar bought a small water pump for his aquarium. The pump delivers 0.2 L/s at a net head of 2 m…

A:

Q: The throat diameter of a perfect venturi meter is 1.59 inches and is placed horizontally in a pipe…

A:

Q: The throat diameter of a perfect venturi meter is 1.87 inches and is placed horizontally in a pipe…

A:

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 30 lit/sec with the velocity of…

A: we know that  Discharge= Area*Velocity Q= A*V Given data Q=30lit/sec =22.2kg/sec V=3.25m/s

Q: Water is flowing upwards through the venture meter shown in the figure. The water volumetric flow…

A: Water flow rate, Q=77 m3/sWater specific gravity, SGw=1Mercury specific gravity, SGHg=13.54Elevation…

Q: Oil (s.g. = 0.84) flows through a 29-in-diameter pipeline at 7214 gpm. Compute the average velocity…

A: Given    Diameter, d = 29 in = 0.736 m   Flow rate, Q = 7214 gpm = 0.4551 m3/s

Q: Q1: If flow rate in pipe shown is (0.5m/s) find the (H). H. water D=300 mm

A:

Q: Determine the overall efficiency of a pump which delivers 2.5 cubic meters per minute of water at…

A: GIVEN DATA- PRESSURE P=341KPa Q=2.5m3/min T=190Nm N=989 rpm WE HAVE TO FIND OVERALL EFFICIENCY

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.