Answered: 2. A fluid (s=0.95) flows through a 77…

Engineering

Mechanical Engineering

2. A fluid (s=0.95) flows through a 77 mm diameter pipe at a velocity of 6 m/sec. Compute the mass flow rate. (kg/s)

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter20: Shop Math And Weld Cost

Section: Chapter Questions

Problem 13R: Find the volume of the following: a. 5 cube b. 10 of 8 pipe

See similar textbooks

Related questions

Q: resolve solution

Q: What is the area of the opening in the duct in square centimeters?

Q: Determine the critical velocity in m/s for Gasoline at 66°C flowing through a 46-mm pipe given that…

A: Given:- d=46mm=0.046m v= 0.00044 m2/s

Q: 10. A ship having a displacement of 24,000 tons and a draft of 34 feet in ocean enters a harbor of…

Q: Completely solve and box the final answers. Write legibly 8. What is the equivalent HP capacity of…

Q: with proper derivatives/integrals and units. Box or indicate your final answers when solving. Use 2…

Q: a faucet is running water at the rate of one half pint every minute. what is this flow rate…

Q: Determine the critical velocity in m/s for Gasoline at 24°C flowing through a 83-mm pipe given that…

Q: Water flows through a horizontal pipe of cross section of 20cm2. At next section the cross sectional…

Q: alculate the average velocity of water through a pipe, in m/s, if the flowrate is 2.1 cubic meters…

A: Given:Flow rate, Q=2.1 m3/hrpipe diameter, d=23 mm

Q: An engineer is designing the runway for an airport. Of the planes that will use the airport, the…

A: Given data: Lowest acceleration rate = a = 2.98 m/s2 Take off speed of the plane = v = 65.69 m/s We…

Q: Water from a hose is being discharged straight vertically upwards until a height of 32 ft. What is…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

100%

2. A fluid (s=0.95) flows through a 77 mm diameter pipe at a velocity of 6 m/sec. Compute the mass flow rate. (kg/s)

Round your answer to 2 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A three stage pump delivers 1.89 m3/s against a head of 200 m with a speed of 2000 rpm. Find the specific speed (US) Round your answer to 2 decimal places. Add your answer
3 Decimals. Like will be given
Please answer the given question and show the solution. Thank you very much! Note: Please include the units in the solution and use 4 decimals point in Final Answer.
A steam turbine has an inlet enthalpy of 2770 kJ/kg with a velocity of 46 m/s. The exit steam condition is 2591 kJ/kg. Solve for the exit velocity. Round your answer to 2 decimal places.
A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount of wind power available. Express the result in MW rounded off to 2 decimal places. Do not write the unit.
with proper derivatives/integrals and units. Box or indicate your final answers when solving. Use 2 decimal places for final answers. 1.) A bus is travelling north at a constant speed of 17m/s. How long will it take for the bus to reach a 5 km stop?
Note: Write the equations used and box the final answer. Write your final answer in two decimal places.
Completely solve and box the final answers. Use 4 decimals at all instances. WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS.
Asap please… 3 Decimals.. Use g=9.81 m/s2, g=32.2 ft/s2. No rounding off in the solutions. Thank youuu
Completely solve and box the final answer. Write legibly 8. A total of 512.5 HP has been rejected from the condenser. If the cooling capacity is 125 gallons per minute of water, compute the temperature of cooling water that enters the cooling tower in degrees F. The cooling water is supplied from the cooling tower at 51.2ºF. Use the standard density of water.
Q. The hydraulic conductivity (K) of an isotropic aquifer is 10 m/day. If the hydraulic head within the aquifer drops 4 m over a distance of 750 m, the groundwater flow velocity within the acquifer is.............m/day. (Up to third decimal place).
Completely solve and box the final answers. Write legibly 7. Compute the discharge velocity of air in ft/s if a turbo-compressor is used to compress 18 pounds per second of air from an initial pressure of 14.8 psi to a discharge pressure of 180 psi with inlet and outlet temperature of 80 degrees F and 708 degrees R, respectively. Use an inlet pipe diameter of 18 inches and outlet pipe diameter of 8 inches.