I got 2 inputs and 1 selector bit for A, but dont understand how I would get B or C The Adder/Subtractor includes a "switch" which is a set of multiplexors. Assume registers Aand B are 32-bits each.a. What is the size of each MUX (number of inputs, number of selector bits).b. How many MUXes are needed?c. How many total selector bits are sent to the adder/subtractor?

adder/subtractor:It is capable of adding and subtracting in same circuit.

Answered: The Adder/Subtractor includes a…

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Design a combinational circuit with four input lines that represent a decimal digit in BCD and four output lines that generate the 9's complement of the input digit. Provide a fifth output that detects an error in the input BCD number. This output should be equal to logic 1 when the four inputs have one of the unused combinations of the BCD code in tinkercad. Just provide even a photo of it. Thank you so much!
1. The following figure shows the four-bit Adder. Your inputs for this combinational circuit are A = 3 and B = 5. What is the outputs S3, S₂, S₁, and So? You have to show how to get the outputs by indicating each carry bit. (Note: You should show all the steps to receive full credits) CA A3 FA B3 S3 C3 A₂ B₂ FA S2 C₂ A₁ B₁ FA S₁ C1 Ao Bo FA So Co
9. A multiplexer is a switching circuit that produces as its single output one of a set of inputs based on the value of some additional inputs called the controls. Given that 0, 1, 2, and 3 in two-bit binary are 00, 01, 10, and 11, respectively, draw a 2-bit multiplexer using the three basic logic gates with inputs xo, x1, x2, and x3, and two control inputs co and c1. Setup the circuit so that x; is the single output, where i if the value of the 2-bit integer (cico)2. NOTE: This is not a Boolean product; instead it's the binary representation of an integer where c1 is the most significant bit and co is the least significant bit.
A B с I Out Write a boolean expression for the circuit shown above. (Note: Do not simplify it.) Write the simplified boolean expression for the circuit based on the truth table.
6. In a(n) circuit, the input values explicitly determine the output. 7. In a(n) existing state of the circuit. circuit, the output is determined by the input as well as the 8. A circuit that computes the sum of two binary digits, taking the input carry bit into account, is called a(n) 9. A(n) based on select signals is a circuit that selects a single output value from a set of inputs 10. A S-R latch is a circuit that can be used as
Implement a 16:1 multiplexer using following instructions: a. Use a combination of 8:1, 4:1 and 2:1 multiplexer. b. You are allowed to use only one 8:1 and one 4:1 multiplexer. c. Identify the correct number of select bits in each multiplexer used.
Design a priority encoder with 4 input lines and 3 output lines. One of the output lines corresponds to if there is a 1 in one of the input lines, and if there is one, then the other two lines correspond to the position of the line. Write the TT for all possible combination of inputs and outputs. Use k-map to find the simplified expression for the output lines. Draw the logic.
There are two major courses A and B, and two minor courses C and D in a department. A student can graduate if he or she passes: Both the major courses A and B or One major course and both minor courses C and D. Design a circuit to determine if the student can graduate or not. Part a: Determine the truth table. Hint: Use the name of the courses as the input variables of your truth table. i.e., A, B, C, D. Variable A is 1 if a student passes course A, otherwise 0. Part b: Write the function in sum of minterms form and simplify using K-map. Part c: Implement the simplified function on proteus and attach its screenshot. Note: Use 4-bit binary of your roll number’s last digit to show output in the screenshot. Part d: Implement the simplified function on virtual breadboard and attach its screenshot. Note: Use 4-bit binary of your roll number’s last digit to show output in the screenshot.
2. Design a combinational circuit with three inputs, x, y, and z, and three outputs, A, B, and C. When the binary input represents any of the decimal digits 1, 2, 3, or 6, the binary output should represent the decimal digit that is one greater than the input, that is 2, 3, 4 and 7, respectively. Similarly, when the binary input represents any of the digits 4, or 7, the binary output should represent the digit that is two less than the input. The remaining two inputs, that are the binary representations of the decimal digits 0 and 5 never occur. Draw the truth table, and give all the minimal forms for the functions that represent the outputs A, B, and C. U
Please explain how you got the inputs!
3. Load the circuit file for decoder 4x16 in multisim. How many inputs and how many outputs does it have? Show Input and outputs

Recommended textbooks for you

Database System Concepts

Computer Science

ISBN:

9780078022159

Author:

Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:

McGraw-Hill Education

Starting Out with Python (4th Edition)

Computer Science

ISBN:

9780134444321

Author:

Tony Gaddis

Publisher:

PEARSON

Digital Fundamentals (11th Edition)

Computer Science

ISBN:

9780132737968

Author:

Thomas L. Floyd

Publisher:

PEARSON

Database System Concepts

Computer Science

ISBN:

9780078022159

Author:

Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:

McGraw-Hill Education

Starting Out with Python (4th Edition)

Computer Science

ISBN:

9780134444321

Author:

Tony Gaddis

Publisher:

PEARSON

Digital Fundamentals (11th Edition)

Computer Science

ISBN:

9780132737968

Author:

Thomas L. Floyd

Publisher:

PEARSON

C How to Program (8th Edition)

Computer Science

ISBN:

9780133976892

Author:

Paul J. Deitel, Harvey Deitel

Publisher:

PEARSON

Database Systems: Design, Implementation, & Manag…

Computer Science

ISBN:

9781337627900

Author:

Carlos Coronel, Steven Morris

Publisher:

Cengage Learning

Programmable Logic Controllers

Computer Science

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

SEE MORE TEXTBOOKS

The Adder/Subtractor includes a “switch" which is a set of multiplexors. Assume registers A and B are 32-bits each. a. What is the size of each MUX (number of inputs, number of selector bits). b. How many MUXes are needed? c. How many total selector bits are sent to the adder/subtractor?