Design a priority encoder with 4 input lines and 3 output lines. One of the output lines corresponds to if there is a 1 in one of the input lines, and if there is one, then the other two lines correspond to the position of the line. Write the TT for all possible combination of inputs and outputs. Use k-map to find the simplified expression for the output lines. Draw the logic.

Design a priority encoder with 4 input lines and 3 output lines. One of the output lines corresponds to if there is a 1 in one of the input lines, and if there is one, then the other two lines correspond to the position of the line. Write the TT for all possible combination of inputs and outputs. Use k-map to find the simplified expression for the output lines. Draw the logic.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Design a combinational logic that compares X and Y, where X ¼ X1X0 andY ¼ Y1Y0; the output of combinational logic is 1, when X < Y; otherwise theoutput is 0.(a) Show truth table.(b) Find output function using K-map.
Design a code converter that converts an unsigned number a into its negative 2's complement representation -a. Specifically, the circuit has two inputs: a1 and ao, and three outputs: b1 and bo (the equivalent to -a) and valid, which is 1 when -a can be represented in 2's complement and O otherwise. 1. Write the truth table for the code converter. 2. Give the simplest SOP expressions for the functions b1, bo, and valid.
The test .. is active when using Boolean difference technique in the logic circuit that illustrated below * .with fault is C6/1 C3 X1 C5 C4 X2 C7 F C2 C6 C1 t3 t0 t2 and t3 t0 and t1 O
Design a code converter that converts a decimal digit from Gray Code to BCD code. Show the following: a. Truth table b. Simplified Boolean function of the output variables using map method. Logic Diagram using XOR/XNOR implementation if possible C.
Use any digital logic simulator Fill-in the blank boxes with the correct LOGIC GATE/ Full/Half Adder
Design a circuit with 3 inputs and 3 outputs, when the binary input is m0, m1, m2 and m3 the output is input plus two and when the input is m4, m5, m6 and m7 then the output is three less then input use k-Map to get the simplified circuit.
Design a-full subtractor with two multiplexers (MUXS) S(xy2) = E(...). C(xy2) = E(...). Connect the variable z to the data inputs. Connect the variables x and y to the selection inputs. 3. %3D
Design a 2-bit comparator. The comparator input has two 2-bit numbers A and B. A consists of 2 bits a1 and a0. B consists of 2 bits b1 and b0. The comparator has three outputs Z2, Z1, Z0. a. Show the truth table for this comparator. b. Write the logic equation for Z2 that are true if only if A < B c. Write the logic equation for Z1 that are true if only if A > B d. Write the logic equation for Z0 that are true if only if A = B e. Show the logic design for this comparator using the minimum number of AND, OR, and Inverters. f. Verify your design using Logisim.
draw the given expression after that simplify the given expression
From the circuit below : A B- Cin -Cout a. From the input signal A,B,Cin draw the output signal S and Cout b. If possible, simplify the circuit and draw the simple circuit INPUTA INPUT INPUT- OUTRUT Cout
stion : 1/1 a Implement the function F (A, B, C) = E(1, 2, 4, 5, 7) a. Using a 2x4 decoder and any logic gates. b. Using a 4:1 multiplexer. P Type here to search 60
a. Write a sum-of-products Boolean expression bexp3 for the output ? of this truth table. b. Draw a circuit that is a direct translation of bexp3 without any simplification. For the circuit, try to use the same input order and layout convention as in the example shown below