The above figure (not drawn to scale) shows a 4 m long beam subjected to a force F and a uniformly distributed load UDL. Given, F=30 kN, UDL = 24 kN/m Length X = 1m, Length Y = 1 m Calculate R₁ and Rr the vertin

The above figure (not drawn to scale) shows a 4 m long beam subjected to a force F and a uniformly distributed load UDL. Given, F=30 kN, UDL = 24 kN/m Length X = 1m, Length Y = 1 m Calculate R₁ and Rr the vertin

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2. The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall thickness of 20 mm loaded in bending with force F = 50 kN. F Ra I: Young's modulus of the beam is 60 GPa.. Calculate the second moment of area, I, in m4 in the form ax 106 where the number a is correct to two decimal places. M: 1 m x 10 m4 Calculate the maximum bending moment, M, in kilonewtonmetres (kNm): σ: kNm E: 1 m Calculate the maximum bending stress, o, in megapascals (MPa) correct to two decimal places. Rb MPa Hence, calculate the maximum compressive strain, e, Enter your answer in micro-strain correct to two decimal places: micro-strain Type here to search 91 DELL 80°F
Analyze the simply supported beam shown in figure-6, by drawing its Shear Force and Bending Moment Diagram. (CLO-2) 50 N 150 N.m 2m Rp 4 m 2 m RA Figure - 6
Of a column of infinite length to points A, B, C and D parallel FA, FB, FC and FD (kN) respectively Using the forces in the directions given in the figure, equivalent resultant force (FEŞ) size and application x and y (m) coordinates of the point find. FA=20 FB=55 FC=35 FD=77 xA=13 yA=8 xB=3 yB=5 xC=10 yC=0 xD=-9 yD=-15
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = Vnin 47000L+9PL )N %3D 54 The reaction at the Roller = Vroller = 61000L+9PL 54 N and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
For the beam and loading shown in Figure 5, determine the value of (r) at the point of action of the resuitant force of the distributed load using point B as the origin. Parabola Vertex 2000 N/m 900 N/m B 6 m A Figure 5: A parabolic distributed load on a beam AB. Answer: If the loading were analysed using point A as the origin, would the value of w at the location of the resultant change? Select one: a. No b. Yes
Find the Nominal force, N in kilo Newtons (kN). What is the shear force, V in kilo Newtons (kN). Find the bending moment, M in kilo Newton metres (kNm).
Could anybody solve this problem and expaine please?
What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant dorce of the triangular distributed load in the figure below.
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
Question 1) For the beam whose loading condition is given in the figure, the force F is F = 18 kN , the distributed load w is w = 10 kN / m , the moment M is M = 14 kN.m and the length L is L= 9 m . According to this; M kN.m w kN/m F kN 3 В L Question 1-A) Find the support reactionat point A in the x direction (A x ). (Enter your result as kN without writing units.) Question 1-B) Find the support reaction at point A in y direction (A y). (Enter your result as kN without writing units.) Question 1-C) Find the support reaction in the y direction ( B y) at the B point . (Enter your result as kN without writing units.)
Please only include the sketch mentioned in the question as I have already provided the calculation and answers to the question.
A storage rack to hold the paper roll. Find force reactions and draw the shear and moment diagrams for the mandrel that extends half of the roll. Use singularity functions for this problem. Givens stanchion paper roll Density=984 kg/m^-3 OD=1.5 m ID=0.22 m L=3.23 m Density=mass/volume So W=(density*volume)*gravity Volume of hollow cylinder= (pi/4)(OD^2-ID^2)*Length of cylinder Length of mandrel=1/2 of L=>1.615 m mandrel base Assumptions: The storage rack is acting with a fixed support With a distributed load of "w" where w is the weight distrubuted